H3C S9500 Series Installation Manual Download Page 1

Page: 1 / 38

Installation Manual
H3C S9500 Series Routing Switches

Table of Contents

Table of Contents

Appendix B Installation of B68 Cabinet ......................................................................................B-1

B.1 Installation Overview .........................................................................................................B-1

B.1.1 Precautions .............................................................................................................B-1

B.1.2 Introduction to the Installation.................................................................................B-1

B.2 Cabinet Installation on the Cement Ground ......................................................................B-1

B.2.1 Introduction to Anchor Plate ...................................................................................B-2

B.2.2 Installation Flow ......................................................................................................B-3

B.2.3 Cabinet Positioning.................................................................................................B-3

B.2.4 Cabinet Leveling .....................................................................................................B-6

B.2.5 Cabinet Combination Connection ...........................................................................B-7

B.2.6 Cabinet Fastening...................................................................................................B-9

B.2.7 Insulation Test.......................................................................................................B-11

B.3 Cabinet Installation on Raised Floor ...............................................................................B-13

B.3.1 Introduction to Support and Slide Rail ..................................................................B-14

B.3.2 Installation Flow ....................................................................................................B-16

B.3.3 Support Positioning...............................................................................................B-17

B.3.4 Installation of Support and Slide Rail....................................................................B-20

B.3.5 Installing Supporting Accessories of Raised Floor ...............................................B-25

B.3.6 Cabinet Leveling ...................................................................................................B-26

B.3.7 Cabinet Combination Connection .........................................................................B-27

B.3.8 Cabinet Fastening.................................................................................................B-29

B.3.9 Insulation Test.......................................................................................................B-31

B.3.10 Floor Recovery....................................................................................................B-31

B.4 Quakeproof Reinforcement of Cabinet............................................................................B-33

Summary of Contents for S9500 Series







































Search results

Summary of Contents for S9500 Series

Reviews:

Related manuals for S9500 Series

Brands by name

Popular brands

H3C S9500 Series, Installation Manual

Search results

Summary of Contents for S9500 Series

Reviews:

Related manuals for S9500 Series

Brands by name

Popular brands