background image

PRODUCT SPECIFICATION 

Hot Water Tap 

Drip Tray 

Drain Cap 

Wire Condenser 

Hot Water Indicator Light 

Cold Water Indicator Light 

Cold Water Tap 

Cold Water 

Temp. Control 

Back Type float sensor 

Cold water 

reservoir 

Hot water 

reservoir 

WATER FLOW DIAGRAM 

UF system 

Stage  1 

- The Sediment  Filter  maximizes the effect  of  water purification by 

eliminating rust,  sand,  silt,  and pipe turbidity that is  found in water supplies 

across the globe. 

Stage 2 

- This filter uses granulated activated carbon media from the Kuraray 

Carbon  Company,  tested  and  certified  by  the  NSF.  It  removes  chlorine, 

TH M's,  Benzene, Pesticides, Insecticides, and other contaminants that may be 

present in  municipal  water supplies. 

Stage 3 

- The Ultra Filtration  Membrane filters  water down to .002  microns, 

and  is  highly  effective  at  removing  bacteria,  organic  chemicals,  and  other 

water borne microorganisms. 

Stage 4 

- This  filter utilizes proprietary  carbon  block technology to ensure 

that 99% of all  chlorine,  lead,  and microbial cysts have been removed. It also 

provides a  "polishing" effect, giving the water a crisp and delicious taste. 

-

H 2 0 - 5 0 0   B O T T L E L E S S   W A T E R  C O O L E R  I N S T A L L A T I O N  & O W N E R S  M A N U A L 

Pure n Natural Systems, Inc. | purennatural.com | 1-800-237-9199

Summary of Contents for H20-500







Reviews: