GYS GYSTECH 7000 Manual Download Page 4

 

8/33 

a- - Before connecting or disconnecting the battery leads, the power cord should be removed from 

the mains. 

b- Connect the red wire (“+”) to the positive (“+”) pole of the battery and the black wire (“-“) to 

the negative (“-“) pole. 

 

 Permanent connection to the vehicle battery (cable with eyelet terminals = accessories n°15) 

Warning : during the mounting, do not connect the charger to the cable with eyelet terminals. 

a- Connect the red cable to the positive battery’s pole 

b- Connect the black cable to the negative battery’s pole 

c- Fix your cable to the vehicle chassis 

Make sure that the cable is not being pinched or in contact with warm surfaces or sharp edges. 

d- After this, the quick contact of the charger can be connected. 

  After charging, disconnect the battery charger from supply mains. Then remove the chassis 

connection and the battery connection, in this order. In case of permanent connection to the 

vehicle battery, first disconnect the battery charger from supply mains, then from the battery 

connection. 

 

S

UGGESTED MODES AND SELECTION

 

 

Gystech 7000 provides 5 modes : 2 charging modes and 3 specific modes. 

To select your charging mode, please refer to the following table and explanations (page 4 and 5 : 

charging modes and specific modes) : 

 

 

M

ODES

 

 

 

 

                                        LED

 

BATTERY USE

 

 

BATTERY 
VOLTAGE

 

&

 SIZE

 

EMERGENCY

 

(i.e.alarm)

 

  IN CYCLE

*

 

(=charging/discharging ; 

i.e. : sweeper…)

 

AUTOMOBILE

  

(battery with 

or without 

maintenance)

 

C

h

ar

gi

n

g m

ode

 

12V 

 

 

 

 

Normal 

condition 

12V 

14 to 230 Ah 

 

 

 

 

 

Cold 

condition 

24V 

 

 

 

 

Normal 

condition 

24V 

14 to 120 Ah 

 

 

 

 

 

Cold 

condition 

S

pe

ci

fi

c m

ode

 

13,6V / 

Max 

 

 

 

 

 

 

12V 

14 to 230 

Ah 

Recover 

 

 

 

 

 

 

12V 

14 to 230 

Ah 

Supply 

5A 

 

 

 

 

 « Alimentation » mode 

(substitute battery) 

* Remark: to recharge sealed batteries used in cycle, select the « cold » mode.

 

 

Select charging mode  

At the beginning of the charging process, the charger begins functioning in the last operation mode 

(except in the 13,6V/Supply mode or 16V Boost mode) and automatically checks the voltage of the 

battery (12V/24V). Press on      to select another mode between the charging modes which are 

suggested in the following order : 

 

12V batteries 

24V batteries 

 

 

 

 

 

 

 

 

 

130.ua — all for cars!

130.ua

Summary of Contents for GYSTECH 7000









Reviews: