29
POWERDUCTION 37LG / 39LG / 50LG
EN
Translation of the original instructions
NB : In the event of a warning alarm, the machine does not work.
The machine is fitted with several protection systems against electrical overcharge and cooling faults. The thermal
protection of the inductor is mainly used when heating stainless steel, copper or aluminium parts. To reactivate the
machine, simply wait for the cooling phase to end. For other protections, switch off the machine using the main switch
and switch it back on.
For fault alarms E-6 and E-7, check that there is no leak or an obstructed/broken hose, that the pump is not blocked or deacti-
vated and that there is enough cooling liquid in the tank.
If the problem appears to have been rectified, press the «inductor change» button twice (10) . The cooling circuit is performing
a purge cycle. It is ready to operate.
TIME DELAY MODE
*
* Valid only for Powerduction versions of V4 program versions. Previous versions are not equipped with this function.
The “Timing” function allows you to control the heating time of the Powerduction.
The time is adjustable from 1 to 30 s.
To enter this mode:
1.
Press the heating authorization button (2). Its indicator light comes on.
2.
Then press both power adjustment buttons (4) simultaneously. The display shows “SEC” then “T 00”
or “SEC” then “ON” if a time has already been set.
3.
The power setting buttons (4) become time setting buttons. Change the setpoint from time to time as desired.
If the time value has not been changed beyond 3 seconds and still shows “T 00”, the Powerduction returns to normal
mode.
Use in “Timer” mode:
Once the time setpoint has been selected, the product is ready for operation. The lighting LED (12) is lit.
1.
Press the lance button (11). The intensity of the LED (12) decreases to indicate that the heating is active.
2.
The heating stops at the end of the time limit. As long as the lance button (11) is pressed, the LED (12) and the
heating enable button (2) flash to warn that the power is off. Adjust the time setpoint if necessary.
3.
Press the lance button (11) for a new heating cycle.
Exit the “Timer” mode
The mode remains active at all times, even when the Powerduction is switched off and then on again.
1.
To exit the mode, set the time setpoint on ∞ or press both power control buttons (4) simultaneously. The Powerduc
-
tion returns to normal operating mode. The display shows “SEC” then “OFF”.
Special feature of the power setting in this mode
As explained, in normal use mode the setting buttons allow you to change the power while in this mode they change
the time setpoint. To change the power without leaving the mode:
1.
Press the heating authorization button (2). Its green light goes out.
2.
The setting buttons (4) allow you to change the power. Adjust the power.
3.
Press button (2) again. Its indicator light comes on again. The setting buttons (4) become the time setting again.
«ACCESSORY CHANGE» MODE
STOP
OK
A
B
1
3
4
5
product serigraphy
Tightening torque max = 7N
This mode is accessible only if the heating isn’t activated (green button switched off).
Summary of Contents for 055599
