background image

 

2

WARNINGS 

THIS CHARGER SHOULD BE USED TO CHARGE ONLY LEAD ACID OR GEL 

CELL TYPE BATTERIES.  USE ON OTHER BATTERY TYPES MAY EXPLODE AND 

CAUSE PERSONAL INJURY. 

 

RISK OF EXPLOSIVE GASES!  WORKING IN THE VICINITY OF LEAD ACID 

BATTERIES IS DANGEROUS.  BATTERIES GENERATE EXPLOSIVE GASES 

DURING NORMAL OPERATION.  THEREFORE IT IS OF THE UTMOST 

IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER YOU 

FOLLOW THE INSTRUCTIONS EXACTLY. 

 

 

Personal Safety Precautions 

Adhere to the following personal safety precautions when installing or working with the 
chargers: 

1. 

Someone should be within voice range or close enough to come to your aid when 

you work near a lead-acid battery. 

2. 

Have  plenty  of  fresh  water  and  soap  nearby  in  case  battery  acid  contacts  skin, 

clothing, or eyes. 

3. 

Wear complete eye protection and clothing protection.  Avoid touching eyes while 

working near a battery.  

4. 

If  battery  acid  contacts  skin  or  clothing,  wash  them  immediately  with  soap  and 

water. If acid enters the eye, flood the eye with cold, running water for at least ten 

minutes and get medical attention.  

5. 

Never smoke or allow an open flame in the vicinity of the battery. 

6. 

Do not drop a metal tool onto the battery.  It may spark, short circuit the battery and 

may cause an explosion. 

7. 

Remove all personal metal items such as rings, bracelets, necklaces, and watches 

when working near a lead-acid battery.  A battery can produce short circuit currents 

high enough to weld a ring or the like to metal, causing a severe burn. 

 

Preparing to Charge Precautions 

Before charging a battery with the charger, read the following precautions: 

1. 

Do 

NOT

 operate the charger if the cables or an LED is damaged. 

2. 

Make sure all accessories on the product you are charging are 

OFF

3. 

If  the  battery  or  batteries  must  be  removed  from  the  product,  always  remove  the 

grounded terminal from the battery first. 

4. 

Be  sure  the  area  around  the  battery  is  well  ventilated  while  the  battery  is  being 

charged.    Gas  can  be  forcefully  blown  away  using  a  piece  of  cardboard  or  other 

non-metallic material as a “hand fan”. 

5. 

Clean battery terminals.  Be careful to keep corrosion from coming in contact with 

eyes. 

Summary of Contents for Trolling Charger 2613A














Reviews: