GÜDE Expert Power Control 1104, Manual

Page: 57 / 101

57
Expert Power Control 1104 / 1105 © 2022 GUDE Systems GmbH
Specifications
4.6.1
Device MIB 1104
Below is a table of all device-specific OID 's which can be accessed via SNMP. In the
numerical representation of the OID the prefix " 1.3.6.1.4.1.28507 " (Gude Enterprise
OID) was omitted at each entry in the table to preserve space. The example for a com-
plete OID would be "1.3.6.1.4.1.28507.68.1.1.1.1". A distinction is made in SNMP OID 's
in between tables and scalars. OID scalar have the extension ".0" and only specify a
value. In SNMP tables the "x" is replaced by an index (1 or greater) to address a value
from the table.
Name OID Type Acc.
Description
epc1104TrapCtrl .68.1.1.1.1.0 Integer32 RW
0 = off 1 = Ver. 1 2 = Ver. 2c 3 = Ver. 3
epc1104TrapIPIndex .68.1.1.1.2.1.1.x Integer32 RO
A unique value, greater than zero, for each receiver slot.
epc1104TrapAddr .68.1.1.1.2.1.2.x OCTETS RW
DNS name or IP address specifying one Trap receiver slot. A port can
optionally be specified: 'name:port' An empty string disables this slot.
epc1104portNumber .68.1.3.1.1.0 Integer32 RO
The number of Relay Ports
epc1104PortIndex .68.1.3.1.2.1.1.x Integer32 RO
A unique value, greater than zero, for each Relay Port.
epc1104PortName .68.1.3.1.2.1.2.x OCTETS RW
A textual string containing name of a Relay Port.
epc1104PortState .68.1.3.1.2.1.3.x INTEGER RW
current state a Relay Port
epc1104PortSw itchCount .68.1.3.1.2.1.4.x Integer32 RO
The total number of sw itch actions ocurred on a Relay Port. Does not
count sw itch commands w hich w ill not sw itch the ralay state, so just
real relay sw itches are displayed here.
epc1104PortStartupMode .68.1.3.1.2.1.5.x INTEGER RW
set Mode of startup sequence (off, on , remember last state)
epc1104PortStartupDelay .68.1.3.1.2.1.6.x Integer32 RW
Delay in sec for startup action
epc1104PortRepow erTime .68.1.3.1.2.1.7.x Integer32 RW
Delay in sec for repow er port after sw itching off
epc1104PortResetDuration .68.1.3.1.2.1.8.x Integer32 RW
Delay in sec for turning Port on again after Reset action
epc1104NTPTimeValid .68.1.5.15.1.0 INTEGER RO
Show if valid Time is received
epc1104NTPUnixTime .68.1.5.15.2.0 Unsigned32 RO
show received NTP time as unixtime (secs since 1 January 1970)
epc1104NTPLastValidTimestamp .68.1.5.15.3.0 Unsigned32 RO
show seconds since last valid NTP timestamp received
epc1104SensorIndex .68.1.6.1.1.1.x Integer32 RO
None
epc1104TempSensor .68.1.6.1.1.2.x Integer32 RO
actual temperature
epc1104HygroSensor .68.1.6.1.1.3.x Integer32 RO
actual humidity
epc1104InputSensor .68.1.6.1.1.4.x INTEGER RO
logical state of input sensor
epc1104AirPressure .68.1.6.1.1.5.x Integer32 RO
actual air pressure
epc1104Dew Point .68.1.6.1.1.6.x Integer32 RO
dew point for actual temperature and humidity
epc1104Dew PointDiff .68.1.6.1.1.7.x Integer32 RO
difference betw een dew point and actual temperature (Temp -