manualshive.com logo in svg

GTO PRO SL-1000, Installation Manual

Share
Download
GTO PRO SL-1000 Installation Manual Download Page 43

40

ACCESS-

ORIES

GTO Low Voltage Wire (RB509)

The 16 gauge dual conductor, multi-
stranded, direct burial low voltage wire
is required to connect the control board
to the solar panel or the AC
transformer. This wire is also required
for installation of some
accessories such as keypads, locks, or
push buttons (available in 1000' rolls
and specially cut lengths).

Splice Kit - Direct Burial (RB708)
When direct burial wire running
below ground needs to be spliced
the RB708 splice kit must be used.

Splice Kit - Above  Ground  (RB707)

For providing secure and moisture
resistant above ground splices for
solar panels, key pads, push buttons
and other accessories using GTO low
voltage wire.

Master

®

 Pin Lock (RB975)

for GTO/PRO SL-2000/2200

The pin lock can be inserted in the
chain brackets of the GTO/PRO SL-
2000/2200 to prevent unauthorized
removal of the quick release pins.

Operator Solar Panel (FM123 )

 - Improved, Amorphous Silicon (Two Year Warrant

*

)

This 10 watt solar panel is a battery charger for use with GTO/PRO Low Voltage Automatic Gate Operator
systems. Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting
clips, wire connectors, and 8 ft. of low voltage wire (for longer lengths, see RB509).  All GTO low voltage
operators are pre-wired for solar panels.  Installation in some regions of the world will require multiple panels for
adequate charging power. Recommended for GTO/PRO 2000/2200, GTO/PRO SL-1000/SL-1200.

Operator Solar Panel (FM122 ) 

- Improved Amorphous Silicon (Two Year Warrant

*

)

The 5 watt solar panel is a battery charger for use with GTO/PRO Low Voltage Automatic Gate Operator
systems. Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting
clips, wire connectors, and 8 ft. of low voltage wire (see Low Voltage Wire for longer wire).  All GTO low volatge
operators are pre-wired for solar panels.  Installation in some regions of the world will require multiple panels for
adequate charging power. Recommended for GTO/PRO 1000, GTO/PRO 1200 and the GTO Bulldog Gate
Lock.

Dual gate installations require minimum of two (2) 5 watt solar panels for adequate charging power.

Summary of Contents for PRO SL-1000














































Reviews:

No comments

Brands by name

Popular brands

Load more brands