background image

3

hedgehogs and moles are active at 
night. They can potentially be harmed 
by the product.

• The product must never be allowed 

to collide with persons or other 
living creatures. If a person or other 
living creature comes in the way 
of the product, it shall be stopped 
immediately.

• Do not put anything on top of the 

product or its charging station.

• Do not allow the product to be used 

with a defective guard, blade disc or 
body. Neither should it be used with 
defective blades, screws, nuts or cables. 
Never connect a damaged cable, or 
touch a damaged cable before it is 
disconnected from the supply.

• Do not use the product if the STOP 

button does not work.

• Always switch off the product when it 

is not in use. The product can only start 
when the correct PIN code has been 
entered.

• The product must never be used at 

the same time as a sprinkler. Use the 
Schedule function so the product and 
sprinkler never run simultaneously.

• Gtech does not guarantee full 

compatibility between the product and 
other types of wireless systems such 
as remote controls, radio transmitters, 
hearing loops, underground electric 
animal fencing or similar.

• Metal objects in the ground (for 

example buried electrical cables) 
can result in a stoppage. The metal 
objects can cause interference with the 
loop signal which then can lead to a 
stoppage.

• Be aware that pets may dig or disrupt 

the perimeter wire, so check regularly.

  Electrical safety:

• Do not operate the mower in explosive 

atmospheres, such as in the presence 
of flammable liquids, gases or dust. 
Mowers can sometimes create sparks, 
which may ignite the dust and fumes.

• Avoid body contact with earthed or 

grounded surfaces, such as pipes. There 
is an increased risk of electric shock if 
your body is earthed or grounded.

• In the event of a thunderstorm: To 

reduce the risk of damage to electrical 
components in the product and the 
charging station, we recommend that all 
connections to the charging station are 
disconnected (power supply, boundary 
wire and guide wire) if there is a risk of a 
thunderstorm.

• Do not handle the charge station or the 

mower with wet hands.

• Regularly check the power supply 

and charge station cables for signs of 
damage or ageing.

• Do not expose the mower to 

temperatures exceeding 80ºC, for 
example leaving the mower in direct 
sunlight or in the hot boot of a car for 
prolonged periods.

  Battery safety:

• This product contains Li-Ion batteries. 

Do not incinerate batteries or expose 
to high temperatures, as they may 
explode.

• After heavy use or in high temperatures 

the battery may become warm. Allow 
the product to cool for 30 minutes 
before charging.

• Operation and storage temperature is 

0-50 °C / 32-122 °F. Temperature range 
for charging is 0-45 °C / 32-113 °F. Too 
high temperatures might cause damage 
to the product.

4719_Robot_Mower_manual_aw3.indd   3

4719_Robot_Mower_manual_aw3.indd   3

20/04/2021   16:21

20/04/2021   16:21

Summary of Contents for RCLM001

































Reviews: