Gtech GWT154 User Manual Download

Page: 42 / 72

. 96-1886-01E

Rev

1.1

GTECH Aircon Radio (Model GWT154)

PAGE

Bytes: 1

Field: 0x01

Code

Length

Mode

Structure 10: Coordinator Initialize Packet

Mode:

0x00

Null. No operation.

0x01

to 0x0F Reserved.

0x10

Select un-configured. Neither a Coordinator nor End-Device radio.

0x11

Selects Coordinator radio mode.

0x12

Selects End-Device radio mode.

0x13 to 0x1F

Reserved.

0x20

Start Network. If Coordinator mode selected, start the PAN.

0x21

Stop Network. If Coordinator mode, disable the PAN.

0x22 to 0x2F,

Reserved.

0x30

Stop Joining. If Coordinator mode, stop responding to any new associate
requests. If End-Device, stop requesting to join a PAN.

0x31

Enable Joining. If Coordinator mode, respond to associate requests from
End-Device radios.

0x32

Request Joining. If End-Device, begin issuing periodic associate
requests to known PANs.

0x33 to 0x3f

Reserved.

0x40

Save Non-volatile memory. Saves persistent radio configuration
parameters to Flash memory.

0x41

Erase Non-volatile memory. Restores radio configuration parameters in
Flash memory to factory default values.

0x42 to 0x7E

Reserved.

0x7F

Reset. If Coordinator, broadcasts reset message to radios in PAN.

7.2.2.3

Get Channel Mask (0x02)

Returns the current 802.15.4 / 2.4GHz Channel Mask bit settings.

Bytes: 1

Field: 0x02

Code

Length

Channel

Mask

Default

Channel

Structure 11: Channel Mask Status Packet

Channel Mask:

2.4GHz 802.15.4 Channel Mask bit fields.

Summary of Contents for GWT154









































































Search results

Summary of Contents for GWT154

Reviews:

Related manuals for GWT154

Brands by name

Popular brands

Gtech GWT154, User Manual

Search results

Summary of Contents for GWT154

Reviews:

Related manuals for GWT154

Brands by name

Popular brands