background image

 

25 

ZY120 1-3kVA User Manual EN rev.08.docx

 

of the UPS

 

UPS

 

57

 

Warn: 

Inverter 

overload timeout

 

Load  is  over  the 

capacity  of  the  UPS 

and  timeout,  UPS  will 

transfer  to  bypass 

mode  if  bypass  is 

available

 

Remove  some  loads  to  under  95%, 

UPS  will  transfer  to  inverter 

automatically

 

65

 

Warn: Battery low

 

UPS  works  in  battery 

and  battery  voltage  is 

low

 

Recover  input  power  or  save  data 

upon “battery low”

 

71

 

Fault: 

Charger 

fault

 

There  is  no  charger 

output.

 

Please  contact  with  distributer  or 

service center

 

72

 

Warn:  input  over 

current

 

Abnormal large current 

enter in rectifier.

 

Please  contact  with  distributer  or 

service center

 

74

 

Warn: 

Manual 

shutdown

 

UPS  will  shutdown 

output  or  transfer  to 

bypass mode

 

/

 

/

 

Battery  discharge 

time diminishes

 

The  battery  has  not 

been fully charged

 

Charge the battery for more than 10 

hours

 

UPS is overload

 

Check  the  loads  and  remove  some 

devices

 

Battery aged

 

Replace the batteries. Please contact 

with  distributer  or  service  center  to 

obtain  replacement  components  for 

batteries.

 

NOTICE

 

Please provide the following information when reporting fault UPS:

 

1) 

The UPS model and serial NO.

 

2) 

The warn and fault code happened

 

3) 

Detail of fault, include LED indicates, buzzer beeps, power condition, load capacity 

and configuration of battery(long backup time model)

 

 

 

Summary of Contents for ZY120
































Reviews: