background image

 

19 

battery is not fully charged (the battery level icons lit one after another 

circularly). When the battery is fully charged, all the level icons are turned 

on. 

1) When operating in bypass mode, the UPS beeps every 2 minutes. If the 

“Function” key is pressed for more than 2 seconds, the alarm will not 

beep 

(

silence function

)

. Press the “Function” key more than 2 seconds 

again to resume the alarm function. 

2) If the utility power indicator blinks, it shows that the voltage or 

frequency of the utility power is out of the input range of the UPS or 

there are problems with reversed polarity (L/N) of site wiring or 

disconnect to the ground for protection. 

3) The other four display pages are load percent page, actual load page, 

input information page and the maximum temperature page. 

Notes:

 

When operating in bypass mode, the backup function of the UPS is not 

available and the power used by the load is directly from the utility 

power via internal EMI filter. 

 

 

 

 

 

Figure 5-4 Bypass Mode 

5.2.4 LCD indication of UPS alarm status and faults 

In the event of an UPS fault, UPS enters fault operation mode, at this point, 

the fault icon turns on consistently, the buzzer beeps continuously and the 

data information area shows current fault code (refer to table 6-2), the 

display on the front panel is shown as the figure 5-5, users can switch to 

output page by pressing function button. 

 

20 

 

 

 

 

 

 

 

Figure 5-5 Fault display 

 

When a warning occurred, the fault icon blinks every second, and users can 

switch to the alarm display page shown as the figure 5-6 to check the 

warning code.   

 

 
 
 
 

 

 

Figure 5-6 Alarm display 

 

Summary of Contents for ZS110
















Reviews: