manualshive.com logo in svg

GSM Commander GC0321, User Manual, Page: 47 / 58

Share
Download
GSM Commander GC0321 User Manual Download Page 47

15. FIRMWARE UPDATES

Step 1:

  Download the software package (which includes the firmware for the device) from our website

(

https://www.gsmcommander.com/downloads/software

)

Step 2:

 Run the executable file 

(See 5.6)

Step 3:
 

Connect GSM Commander to PC via the supplied USB cable

Step 4: 
 

Connect power to the GSM Commander

Step 5:

Run the Utility (Start > All Programs [ALL APPS]> GSM Commander V7 > Update Firmware)

The   SmartSetup   software   will   also   automatically   detect   upon   startup   if   the   firmware   currently
loaded on the GSM Commander unit does not match it's current version. It will then prompt you to

run the update firmware utility.

Screen 1:

The loader  utility will show this screen when
started.  

Screen 2:

The  loader   utility   will   now   show  this   screen,

which   means   the   firmware   is   being   updated.

The green LED, labelled  

“STATUS”

  on the

GSM Commander, will start flashing.

On completion the loader utility will close and the unit will start up automatically or if you so wish
you can disconnect the power. 

© Polygon Technologies.   All rights reserved                                                                                          

Page 47

Summary of Contents for GC0321



























































Reviews:

No comments