manualshive.com logo in svg

GSM Commander GC0321, User Manual, Page: 37 / 58

Share
Download
GSM Commander GC0321 User Manual Download Page 37

8.2. Supported THEN Actions

8.2.1. THEN Change Output

A statement containing this Action, will change the selected output according to specified actions.

The user can choose between the following five actions:

•

Activate for a time

•

Activate for a time – Pause – Activate for a time

•

Activate (Leave Activated)

•

De-Activate (Leave De-Activated)

•

Change State

If the user chooses:

➢ 

“Activate for a time”

, it will Activate the selected output for the selected number of seconds specified.

➢ 

“

Activate for a time – Pause – Activate for a time

”, it will Activate the selected output for the selected

number of seconds specified. The output will remain off for a selected period, after which it will again

activate for the selected number of seconds.

➢ 

“

Activate (Leave Activated)

”, it will Activate the selected output and leave it activated. The inverse

applies to “

De-Activate (Leave De-Activated)”.

➢ 

“

Change State

”, it will either change the state of the selected output, meaning that it will active it if it

was de-activated and vice versa.

8.2.2. THEN Send Message

A statement containing this Action, will send a message via SMS to each of up to 6 selected recipients or a
message via Serial port or a message to our server.

The user can choose between the following fourteen options:

•

Plain Message

•

Input / Output Status

•

General Status

•

Analog Input Status 

(Able to define own scale and unit)

•

Global Input Status

•

Global Output Status

•

Please Call Me

•

Baselog Message

•

Log Status to Sever*

If the user chooses:

➢ 

“

Plain Message

”

, it will send a predefined message either via SMS to each of up to 6 selected recipients,

via the serial port or to server*.

➢ 

“

Input / Output Status

”

, it will send a predefined message(one for active and one for inactive) regarding

the status of the selected input or output either via SMS to each of up to 6 selected recipients, via the

serial port or to server*.

➢ 

“

General  Status

”

, it will send a general status message either via SMS to each of up to 6 selected

recipients, via the serial port or to server* containing the following information: date & time, signal

strength, firmware version, serial number, airtime remaining, status of mains power.

➢ 

“Analog Input Status”

, it will send a message either via SMS to each of up to 6 selected recipients, via

the serial port or to server* containing the status of the analog input. The user is able to specify the

maximum and minimum value as well as the unit. The user is also able to define the message to

precede, and the message to follow the analog value.

© Polygon Technologies.   All rights reserved                                                                                          

Page 37

Summary of Contents for GC0321



























































Reviews:

No comments