GSM Commander GC0321 User Manual Download Page 23

Page: 23 / 58

6. CONFIGURATION VIA PC

6.1. Basics

The following is required to configure the GSM Commander:

➢

A PC running Windows XP / Vista / Windows 7 / Windows 8/ Windows 10

➢

Setup utility installed on the PC

(Available on the CD supplied with the product)

or downloaded at

https://gsmcommander.com/downloads/software

➢

USB cable

➢

Power supply

(See sec 6.2)

➢

Antenna

(See sec 6.5)

➢

SIM card(s)

(See sec 6.4)

Please note

The GSM Commander will eventually startup if no SIM card is inserted, but there

would be no GSM functionality, which means none of the GSM features will work.

Follow these steps:

Step 1:

Insert SIM card(s) into unit

(when unit is not powered up)

Step 2:

Connect GSM Commander to PC via the supplied USB cable

Step 3:

Connect power to the GSM Commander

Step 4:

Run the Utility
Start Menu>

All Programs

[

All Apps

] >

GSM Commander V7

Configure GSM Commander

)

The software will show this screen when
started. Here you can select whether you
would prefer opening an existing setup
from a file on your PC, retrieve the setup
currently on the GSM Commander, just
open to the main screen.

Page 23

Summary of Contents for GC0321
























































Search results

Summary of Contents for GC0321

Reviews:

GSM Commander GC0321, User Manual, Page: 23 / 58

Search results

Summary of Contents for GC0321

Reviews: