manualshive.com logo in svg

GSM Commander GC0321, User Manual, Page: 30 / 58

Share
Download
GSM Commander GC0321 User Manual Download Page 30

7.11. IMEI Number

If   you   need   the   IMEI   number   of   the   device,   you   can   send   the   following   command   from   the

Administrator's

 phone / number. It will reply via SMS with the IMEI number. This is very useful if you

need the IMEI number for our online, Airdrive platform, to add a new unit, for example. 

ADMIN IMEI

Please note: 

This function only works with firmware versions 7.43 and above

The only other way to retrieve the IMEI number is, when you have the unit connected via USB in the
SmartSetup software and get it from the STATUS tab.

7.12. Switch SIM card

This set of commands allows you switch from the one SIM card to the other and can only be sent
from the administrator number on a GC-1281 unit only. 

To switch to primary SIM card you must send:

SIM1

To switch to secondary SIM card you must send:

SIM2

To switch from the currently active SIM card to the inactive SIM card you must send:

SIMTOGGLE

7.13. Reset GSM Commander

This command can be sent from ANY number. To reset the GSM Commander you must send:

RESET GSMC

© Polygon Technologies.   All rights reserved                                                                                          

Page 30

Summary of Contents for GC0321



























































Reviews:

No comments