Grundig RS-Set 2 User Manual Download Page 3

12

SET-UP AND SAFETY

______________________________________________

To ensure that these high-quality, easy-to-use loudspeakers provide you with
lasting enjoyment, please observe the following instructions when setting them
up.
These loudspeakers are designed for the playback of wireless audio signals.
Any other use is expressly prohibited.
If the loudspeakers are subjected to sudden changes in temperature, for exam-
ple if they are brought in from the cold to a warm room, let them stand for at
least two hours. Do not connect them to the mains supply during this time.
The loudspeakers are designed for use in dry rooms. You must make sure that
the device is protected from moisture such as rain or splashing water.
When deciding where to place the device, please note that furniture surfaces
are covered by various types of varnish and plastic, most of which contain che-
mical additives. These additives can corrode the device supports, resulting in
residues on the furniture surfaces which are difficult or impossible to remove.
Do not place the loudspeakers close to heating units or in direct sunlight, as this
will impair the internal cooling.
Do not place any vessels containing fluids such as vases on the loudspeakers.
Should they be knocked over, fluid may spill on the electrical components, thus
presenting a safety risk.
Do not open the loudspeaker casing under any circumstances. The manufacturer
will not accept any liability for damage resulting from improper handling.
Thunderstorms are a danger to all electrical devices. Even if the loudspeakers
are switched off, they can be damaged by a lightning strike to the mains.
Always remove the mains plug in the event of an electrical storm.
Clean the gauze of the loudspeakers with a vacuum cleaner from time to time 
(at low vacuum power without exerting any pressure).

°

C

2h

°

C

ǵ

ǵ

ǵ

ǵ

MAINS
230V

50/60Hz

RESET

ǵ

! SER

VICE !

! SER

VICE !

! SER

VICE !

ǵ

MAINS
230V

50/60Hz

RESET

ENGLISH

Summary of Contents for RS-Set 2














Reviews: