Grundfos Redi-Flo 2 Nstallation And Operating Instructions Download Page 15

Page: 15 / 36

PARAMETER LIST FOR REDI-FLO VFD

OPERATOR ADJUSTMENTS

OPERATOR ADJUSTABLE CONTROL FEATURES

Use flowchart below to change operator adjustable control features.

Page 13

Page 14

To Adjust Operator Adjustable Control Features, follow the following
instructions: (See Figure 8)

1. Disconnect Redi-Flo VFD from the power supply.

2. Remove front cover of VFD by losen the two phillips head screws.

3. Lift and set aside the cover to expose the mode keys in the center of the drive.

Use caution to avoid damage to the ribbon cable attaching the front cover to the

interior of the drive.

4. Setting aside the front cover place in a position so the LED display is visible.

5. Connect drive to the power supply.

6. Use the following flow chart to adjust operator adjustable control features.

Figure 8

CAUTION

The internals of the Redi-Flo VFD contain

High Voltages! Extreme caution should be

exercised when making adjustments.

Phillips screws

Note: Shaded functions can be changed during operation.

NO.

DESCRIPTION

RANGE

UNITS

DEFAULT

F00

RF2 Max. Output Frequency

100.0-400.0 Hz

1.0 Hz

400.0 Hz

F01

RF2 Min. Output Frequency

0.0-100.0 Hz

1.0 Hz

25.0 Hz

F02

RF4 Max. Output Frequency

30.0-100.0 Hz

1.0 Hz

100.0 Hz

F03

RF4 Min. Output Frequency

0.0-30.0 Hz

1.0 Hz

25.0 Hz

F04

Acceleration Time (to 100/400 Hz)

0.5-10.0 Sec.

0.5 Sec.

5.0 Sec.

F05

Deceleration Time (from 100/400 Hz)

0.5-10.0 Sec.

0.5 Sec.

5.0 Sec.

F06

Torque Boost (in % max.)

0-30%

F07

Base Frequency Select

50 or 60 Hz

60 Hz

F08

Motor Overload Level Im depends uponRF2/RF4

50-110% Im

% Im

110%

F09

Input Undercurrent Detection Disable

0= Disabled

0-1

(Disabled)

1= Enabled

F10

Input Undercurrent Detection Level

10-60% (1.6-9.6A)

% Im

30%

F11

Input Undercurrent Restart Time

1-99 mins.

1 min.

F12

Switching Frequency

0-2

1 (7.8kHz)

0= 15.6 kHz

1= 7.8 kHz
2= 3.9 kHz

F13

Input Current Enabled

0-1

0= Disabled (23A)

(Disabled)

1= Enabled (16A)

23A

F14

Auto Reference Signal

0-1

0= Disabled

(Disabled)

1= Enabled

F15

No Motor Load

0-1

0= Disabled

(Enabled)

1= Enabled

TR'sVFDIO.p65

5/31/00, 9:02 AM

Summary of Contents for Redi-Flo 2





































Search results

Summary of Contents for Redi-Flo 2

Reviews:

Related manuals for Redi-Flo 2

Brands by name

Popular brands

Grundfos Redi-Flo 2, Nstallation And Operating Instructions

Search results

Summary of Contents for Redi-Flo 2

Reviews:

Related manuals for Redi-Flo 2

Brands by name

Popular brands