Grundfos CIU 202, Functional Profile And User Manual

Page: 30 / 60

English (GB)
30
9.9 Pump 2 register block
All register values are read-only, and 0xFFFF indicates that the
data value is not available.
Unless otherwise stated, the data type used for counters and
scaled values is always an unsigned integer.
Address Register name Scale Description
00451 Pump2.MotorTemperature 0.01 K Motor temperature, pump 2.
00452 Pump2.ElectronicTemperature 0.01 K Electronics temperature, pump 2.
00453 Pump2.AverageLineVoltage 0.1 V Average supply voltage, pump 2.
00454 Pump2.AverageLineCurrent 0.1 A Average supply current, pump 2.
00455 Pump2.AverageLineCurrentLatest 0.1 A Average supply current the last time pump 2 was operating.
00456 Pump2.LineFrequency 0.1 Hz Frequency of power supply, pump 2.
00457 Pump2.PhaseSequence Bool Phase sequence of power supply, pump 2.
00458 Pump2.CosPhi 0.01 Power factor, pump 2.
00459 Pump2.Power 1 W Power consumption, pump 2.
00460
00461 Pump2.EnergyTripCounterHI
Pump2.EnergyTripCounterLO
1 kWh
Energy consumption, pump 2.
Can be reset with register 00101, bit 3:
PitPump2ResetHistory.
00462 Pump2.WaterLevel 0.01 m Water level as estimated by pump 2.
00463 Pump2.WaterLevelMax 0.01 m
Logged maximum value of water level, pump 2.
Can be reset with register 00101, bit 3:
PitPump2ResetHistory.
00464 Pump2.MaxContinousTime 1 minute
Logged maximum value of continuous operating time within
the last 30 days, pump 2.
Can be reset with register 00101, bit 3:
PitPump2ResetHistory.
00465
00466 Pump2.TotalPoweredTimeHI
Pump2.TotalPoweredTimeLO
1 minute
Total time that pump 2 has been powered on.
Used as time stamp for alarms in the alarm log the moment
the alarm appears.
00467
00468 Pump2.OperationTimeHI
Pump2.OperationTimeLO
1 minute Total time that pump 2 has been operating.
00469
00470 Pump2.OperationTimeTripCounterHI
Pump2.OperationTimeTripCounterLO
1 minute
Trip counter of the total time that pump 2 has been
operating.
Can be reset with register 00101, bit 3:
PitPump2ResetHistory.
00471
00472 Pump2.NumberOfStartsHI
Pump2.NumberOfStartsLO
Unscaled Total number of starts, pump 2.
00473
00474 Pump2.NumberOfStartsTripCounterHI
Pump2.NumberOfStartsTripCounterLO
Unscaled Trip counter of total number of starts, pump 2.
00475 Pump2.AlarmCode Unscaled
Grundfos-specific alarm code, pump 2.
See section
14.2 CIU 262
.
00476 Pump2.WarningCode Unscaled
Grundfos-specific warning code, pump 2.
See section
14.2 CIU 262
.
00477 Pump2.OperatingMode Bits
Operating mode of pump 2.
0: "Auto" mode (power-on default)
1: Forced start
2 : Forced stop.
00478
Bit 0: Subpump2AlarmsPhaseSequence Phase sequence reversed
Bit 1: Subpump2AlarmsOvervoltage Overvoltage
Bit 2: Subpump2AlarmsUndervoltage Undervoltage
Bit 3: Subpump2AlarmsOverload Overload
Bit 4: Subpump2AlarmsBlockedMotor Blocked motor/pump
Bit 5: Subpump2AlarmsAlarmBit5 -
Bit 6: Subpump2AlarmsMotorTemperature Motor temperature
Bit 7: Subpump2AlarmsElectronicTemperature Temperature, control electronics
Bit 8: Subpump2AlarmsTermoRelay1 Temperature relay 1 in motor, for example Klixon
Bit 9: Subpump2AlarmsTermoRelay2 Temperature relay 2 in motor, for example thermistor
Bit 10: Subpump2AlarmsVerificationError Verification error, code area (ROM, FLASH)
Bit 11: Subpump2AlarmsAlarmBit11 -
Bit 12: Subpump2AlarmsSensorFault Sensor fault
Bit 13: Subpump2AlarmsAlarmBit13 -