Grundfos BACnet IP Functional Profile And User Manual Download Page 12

Page: 12 / 35

7. Functions

7.1 Functions overview

Valve unit variants

Upgrades

Functions

MIXIT

MIXIT DYNAMIC

DYNAMIC

CONNECT

Temperature controller

•

Underfloor overheat protection (available in underfloor heating systems)

•

Coil preheat and frost protection (available in air handling unit systems)

•

Pump control modes
•

Proportional pressure

•

Constant pressure

•

Constant flow

•

Constant curve/constant speed

•

Outdoor temperature compensation

•

Eco schedule and warm-weather shutdown

•

Pressure independence

•

Limiters
•

Supply flow limit

•

Return temperature limit

•

Thermal power limit

•

Differential power limit

•

Energy monitor

•

Related information

7.2 Temperature controller

7.3 Underfloor overheat protection

7.4 Coil preheat and frost protection

7.5.1 Configuring the pump control mode

7.5.2 Setting the duty point for constant-speed control mode

7.5.3 Setting the duty point for constant-pressure control mode

7.5.4 Setting the duty point for proportional-pressure control mode

7.5.5 Setting the duty point for constant-flow control mode

7.6.1 Setting outdoor temperature compensation

7.7 Eco schedule

7.8 Warm-weather shutdown

7.9 Pressure independence

7.10 Limiters

7.11 Energy monitor

English (GB)

Summary of Contents for BACnet IP




































Search results

Summary of Contents for BACnet IP

Reviews:

Related manuals for BACnet IP

Brands by name

Popular brands

Grundfos BACnet IP, Functional Profile And User Manual

Search results

Summary of Contents for BACnet IP

Reviews:

Related manuals for BACnet IP

Brands by name

Popular brands