background image

10

Revision date: 10.25.12

All end rafters consist of one (1) 94" straight pipe and two (2) curved sections of 

pipe: one pipe has plain ends and one pipe has a plain end and a swaged end that 

is inserted into the plain end of the first pipe.

Complete these steps to assemble the rafters.
1.  Locate the two pipes for the first end rafter: #08R105P2 and #08R105S1.
2.  Assemble the rafters by inserting the swaged (or tapered) end of one pipe into 

the plain end of the other as shown in the diagram to the right. 

Do not install a 

Tek screw to secure the joint at this time.

3.  Locate two (2) 4-way PVC fittings (#105233) and select one straight plain pipe 

approximately 94" long (#105P094375). 

4.  Insert the fittings onto the ends of the pipe as shown until they are seated 

tightly in place. Verify that the base of the end rafter aligns with the base frame 

(A). Adjust as needed. 

Do not Tek screw at this time.

5.  Select one of the assembled rafters and insert the ends of the rafter pipes into 

the 4-way fitting as shown until seated (B). Verify that fittings align with slotted 

baseboards.

6.  With the pipes properly seated, secure the end rafter using FA4482 Tek 

screws (C & D).

7.  Repeat the steps to assemble the remaining end rafter.

3

Assembly Instructions

ASSEMBLE THE END RAFTERS

Install the screw so that its head will 

not interfere with the installation of 

the cover. Photo below shows the 

screw is installed on the underside 

of the rafter assembly.

105233

A

B

C

D

08R105P2

08R105S1

94" Pipe

Step 2

Summary of Contents for Flip-Top Cold Frame
























Reviews: