background image

6

113463_64_65HBC   Revision date: 08.27.19

Prepare and Square Building Site

PREPARE BUILDING SITE

A level site is required to accurately and safely construct building. Consult 

the services of a qualified contractor to properly grade and prepare site.

Site should slope away from building for proper water drainage.

After site is prepared, mark locations of frame corners to square frame 

position. Taking these steps 

before

 shelter assembly begins saves time and 

ensures that structure is square and positioned as desired. 

The following procedures are suggested methods. Their use depends on 

shelter size, shelter use, footings (if applicable), and the method used to 

anchor the shelter. 

When in doubt, consult the services of a qualified contractor experienced 

with the construction of similar structures.

Ground Posts

 

Ground posts can be set in concrete as described within this manual. Or, 

anchor building frame as described in the MUST READ document.  

SQUARE SITE: GENERAL STEPS

1.  Identify a corner where a ground post will be set, drive a stake, and 

string a line the building width. Stake in place. (Width of frame is 

measured from center-to-center of ground posts.)

2.  After placing first corner stake, string a line the frame width (center-to-

center of ground posts) and drive second corner stake.

3.  String a line longer than the building 90° from the line between the first 

and second stakes. 

NOTE:

 A transit can be used to ensure an accurate 90° angle, or the 

3-4-5 rule can be used. Refer to diagram. Using multiples of 3-4-5 such 

as 6-8-10 or 12-16-20 helps to maintain an accurate 90° angle.

4.  After squaring frame position, measure length and drive the third corner 

stake.

5.  Repeat the same step to set last corner stake. 

 

NOTE:

 The distance measured diagonally between 

corner stakes

 must 

be equal for building to be square.

SET GROUND POSTS IN CONCRETE

Sandy or loose soil requires setting ground posts in concrete. Review 

the layout diagrams for additional details. Follow all local and regional 

building codes during construction.

Enlist the services of a professional and competent contractor to 

prepare site and set ground posts.

Failing to secure ground posts in concrete as required may result in 

damage to frame, frame contents, and surrounding property and may 

void warranty.

Shelter width is measured from ground post center to ground post center. 

Length is also measured ground post center-to-center. 

Summary of Contents for 113463H


































Reviews: