Gromako Data & Services Derminator 2 Instructions Manual Download Page 17

Page: 17 / 27

HTTP://DERMINATOR.COM

COMPLIANCE STATEMENTS

FCC

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and

part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for

help.

IMPORTANT: Any changes or modification not expressly approved by the party responsible for compliance could

void the user’s authority to operate the device. Where shielded interface cables have been provided with the product

or specified additional components or accessories elsewhere defined to be used with the installation of the product,
they must be used in order to ensure compliance with FCC regulations.

CANADA

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.

Products with the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive

(73/23/EEC) issued by the Commission of the European Community and if this product has telecommunication

functionality, the R&TTE Directive (1999/5/EC).

Compliance with these directives implies conformity to the following European Norms (in parentheses are the

equivalent international standards and regulations):

EN55022 (CISPR 22) – Electromagnetic Interference

EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11) – Electromagnetic Immunity

EN61000-3-2 (IEC61000-3-2) – Power Line Harmonics

EN61000-3-3 (IEC61000-3-3) – Power Line Flicker
EN60950 (IEC60950) – Product Safety

Summary of Contents for Derminator 2




























Search results

Summary of Contents for Derminator 2

Reviews:

Related manuals for Derminator 2

Brands by name

Popular brands

Gromako Data & Services Derminator 2, Instructions Manual

Search results

Summary of Contents for Derminator 2

Reviews:

Related manuals for Derminator 2

Brands by name

Popular brands