Grohe Blue HOME Series Manual Download

Page: 21 / 96

Technical data cooler/carbonator electrical data:

• Connection:

Wall socket with earth wire, protected

via a 10 A fuse

• Voltage supply:

230 V AC / 50 Hz

• Max. power consumption:

180 W

• Type of protection:

IP21

• Relative air humidity:

max. 75%

• Refrigerant:

0.025 kg - R600a

• Safety shut-off of pump:

approx. 4:30 min

• Operating pressure:

min. 0.2 MPa - max. 1 MPa

Sanitary data:

• Cooler/carbonator cooled water capacity:

1.4 l

• System operating pressure:

max. 0.6 MPa

• Flow rate at 0.3 MPa flow pressure:

approx. 2 l/min

• Ambient temperature:

4 – 32 °C

• Temperature

– Cooler /carbonator water inlet:

max. 20 °C

– Cooled water temperature:

approx. 5 – 10 °C

• Sound pressure level L

A (frestanding):

50 ± 4 dB

• Adjustable bypass, factory setting:

• Filter capacity at bypass setting 2

(Carbonate hardness 17 - 24 °KH):

max. 600 liters

corresponds to max. 12 months

• Water connection

– cooler/carbonator:

cold - blue

Electrical test data

• Software class:

• Contamination class:

• Rated surge voltage:

2,500 V

The test for electromagnetic compatibility (interference emission test)
was performed at the rated voltage and rated current.

Technical data fitting:

• Flow pressure

min. 0,1 MPa/recommended 0,2 - 0,5 MPa

• Operating pressure:

max. 1 MPa

• Test pressure:

1,6 MPa

If static pressure exceeds 5 bar, a pressure-reducing valve must be
fitted.

Avoid major pressure differences between hot and cold water
supply.

• Flow rate at 3 bar flow pressure:

approx. 9 l/min

• Temperature

- Hot water supply:

max. 70 °C

- Recommended (energy saving):

60 °C

Water connection:

cold - right

hot - left

Thermical disinfektion of the fitting is possible.

Installation and commissioning

GROHE recommends a depth of min. 510 mm for
the cabinet.

Flush pipes thoroughly before and after installation

(observe

EN 806)

Adjust bypass of filterhead according to local carbonate
hardness and connect filter cartridge.

The carbonate hardness can be tested by using the enclosed test
strip or the relevant water supplier can provide information on the
carbonate hardness.

The fitting has a system-related run-on time of
approx. 1 second each time carbonated water is drawn.

Note: Make sure that the water inlet hose does not come loose
by movement when installing the cooler.

When transporting or installing the cooler/carbonator,
cooling fluid may have run into the lines. In order to ensure
that the cooling fluid has run back, the cooler/carbonator
may only be switched on following a pause of 24 hours.

Control:

The buttons have the following functions:



Filter replacement reset



Filter size selection and carbontate hardness adjustment



CO2 reset

Display:

In the inactive state, the remaining filter capacity is displayed in
percent.

When carbonat hardness

≤

9° the use of activated carbon filter

(Order no.: 40 547 001) is recommended.

The cooler/carbonator is set for operation with the S-Size filter
cartridge (Prod no.: 40 404 001) at the factory.

For operation with other filter cartridges the cooler/carbonator must be
set out.

Maintenance and Cleaning

Important!
Risk of damage!
Always disconnect the power supply

and interrupt the

supply before carrying out maintenance work on the
system. The plug-in connector can then be disconnected.

Cleaning cooler/carbonator

For hygienic and healthy reasons, the cooler/carbonator must
be cleaned once a year. Cleaning must be performed before
changing the filter cartridge, in order to prevent contamination
of the replacement filter cartridge.

Note: The cleaning kit

(Prod. no.: 40 434 001) and the

accompanying adapter (Prod. no.: 40 694 000 or 40 699 000)
could be ordered at

www.shop.grohe.com.