background image

OM-VRC-3E/VRC-6E  148673 REV. G

Open/Close Handle

Operation

WARNING

ANY POTENTIAL USER OF THE EQUIPMENT MUST BE TRAINED IN SAFE AND CORRECT OPERATING

PROCEDURES.

A.

Controls

Operator controls are on the front right of the unit.

The VRC-3E and VRC-6E control panels have the

following touch pads and indicator lights:

!

The ON/OFF rocker switch gets the

Vortex™ ready for use, or shuts it off.

!

The HOLD indicator light shows that the

cavity is at holding temperature.

!

The

 TIMED

indicator light stays on

when the timer is operating.

!

The ADD WATER indicator light is lit when

it’s time to add water.

!

The open and closed position of the

drain valve allows the unit to be filled

with water or drained.

!

!

The ready indicator light indicate the

unit has achieved the ready temperature.

Temperature gauge indicates internal 

temperature of cavity.

!

Hour meter records cumulative hours of

operation.

!

T

!

The FAULT display shows the 

current fault.

he HI TEMP (error code 6) indicator

comes on when the bottom of the water

reservoir becomes too hot.

OM-VRC-3E/VRC-6E

TIME display

TIMER knob

MANUAL button and indicator
TIMED button and indicator
HOLD button and indicator

CANCEL button and indicator
FAULT display

ON/OFF rocker switch

Temperature gauge

Hour meter

Summary of Contents for Vortex 100 Series















Reviews: