background image

-26-

Model G0818 (Mfd. Since 10/16)

5.  

Use a soft bristle brush and dry rag to remove 
dust from impeller blades and impeller hous-
ing. 

DO NOT

  use  compressed  air  or  your 

bare hands. Inspect impeller for damage and 
replace if necessary.

— Use  only  NFPA  484-compliant  shop  vac-

uum with HEPA filter and non-conductive 
hose to vacuum debris inside housing. 

DO 

NOT

 use compressed air.

6.

  When  complete,  replace  motor/impeller  and 

re-install cap screws and flat washers.

To clean impeller and inspect motor shaft:

1.

  DISCONNECT MACHINE FROM POWER!

2.

  Remove  (8)  cap  screws  and  flat  washers 

from motor mounting plate (see 

Figure 36

).

3.

  Put  on  NIOSH-approved  respirator,  ANSI-

approved safety goggles, and leather gloves.

Cleaning Impeller

The  impeller  normally  requires  no  maintenance, 
but the blades can accumulate metal dust debris 
that  will  adversely  affect  motor  performance. 
Removing  the  motor/impeller  assembly  allows 
cleaning and inspection of the impeller blades.

Tools Needed 

Qty 

Hex Wrench 6mm .............................................. 1
Soft Bristle Brush .............................................. 1
Shop Vacuum with HEPA Filter  
and Non-Conductive Hose ................................ 1
NIOSH-Approved Respirator ............................. 1
ANSI-Approved Safety Goggles ........................ 1
Leather Gloves ...........................................1 Pair

Figure 37.

 Motor/impeller assembly removed for 

cleaning and inspection.

Impeller

4.  

Remove  motor/impeller  assembly  and  care-
fully set it on capacitor cover (see 

Figure 37

).

Figure 36.

 Cap screws secure the motor/impeller 

assembly to the cabinet.

x 8

Motor

Capacitor Cover

Motor 

Mounting 

Plate

Cleaning Ducts

Inspect all ducts and fittings monthly and clean as 
necessary. 

To clean inside ducts:

1.

  DISCONNECT MACHINE FROM POWER!

2.

  Wear  NIOSH-approved  respirator,  ANSI-

approved goggles, and leather gloves.

3.

  Undo clamps to disconnect ducts and fittings. 

Use  soft  bristle  brush  and  dry/damp  rag  to 
remove accumulated metal dust.

4.

  Reconnect ducts and secure clamps.

Summary of Contents for G0818









































Reviews: