88
PL
• Zachować najwyższą ostrożność pod
-
czas cięcia małych gałęzi i konarów.
Cienka gałąź może się zakleszczyć w
pile i odbić w kierunku operatora lub
sprawić, że straci równowagę.
• Nie piłować drewna leżącego na ziemi.
• Podczas cięcia naprężonych konarów
zwracać uwagę na możliwość odbicia,
gdy naprężenie gwałtownie spadnie.
Istnieje niebezpieczeństwo odniesienia
obrażeń.
• W przypadku obrócenia się bądź
zakleszczenia narzędzi tnących w
urządzeniu do obcinania gałęzi nie
należy próbować uwolnić urządzenia
siłą. Urządzenie natychmiast wyłączyć.
Można je ponownie włączyć dopiero po
usunięciu przyczyny zablokowania. Nie
-
bezpieczeństwo odniesienia obrażeń!
ZAGROŻENIA OGÓLNE
Nawet przy przepisowej obsłudze urzą
-
dzenia elektrycznego występują tzw. za
-
grożenia ogólne. W związku z konstrukcją
i sposobem pracy urządzenia elektryczne
-
go mogą występować następujące zagro
-
żenia ogólne:
a) Skaleczenia i rany cięte.
b) Uszkodzenia słuchu w razie nieko
-
rzystania z odpowiednich elementów
ochrony słuchu.
c) Szkody na zdrowiu będące skutkiem
działania wibracji na rękę i ramię,
jeżeli urządzenie jest używane przez
długi czas lub nie jest odpowiednio
prowadzone i przepisowo konserwo-
wane.
Instrukcja montażu
Przed wykonaniem wszelkich prac
przy urządzeniu wyłączyć urządze
-
nie i wyjąć akumulator.
Jeśli rury urządzenia nie są wło
-
żone jedna w drugą i prawidłowo
przykręcone, urządzenie nie
pozwoli się włączyć. Wyłącznik
bezpieczeństwa uniemożliwi pracę
urządzenia!
Stosuj tylko oryginalne części.
Montaż urządzenian
1. Włóż w siebie aż do oporu
koniec sześciokątnej rurki alu
-
miniowej wysięgnika teleskopo
-
wego (10) oraz koniec trzonka
poniżej głowicy tnącej (7).
Podczas montażu zwrócić uwa
-
gę na to, aby nosek (10a) na
sześciokątnej rurce aluminiowej
wszedł do wpustu (7a) na końcu
trzonka (patrz mała ilustracja).
2 Zamocować obydwie części za
pomocą tulei gwintowanej (9).
.
Montaż łańcucha tnącego i
miecza
Przed wykonaniem wszelkich prac
przy urządzeniu wyłączyć urządze
-
nie i wyjąć akumulator.
1. Odkręcić śruby mocujące miecz
(5) i zdjąć osłonę koła łańcucho
-
wego (6) (patrz mała ilustr.).
2. Rozłożyć łańcuch tnący (1) w
pętli tak, aby fazowane krawę
-
dzie tnące ogniw łańcucha były
skierowane w kierunku ruch
wskazówek zegara.
3. Włożyć łańcuch tnący (1) w ro
-
wek miecza.
4. Obrócić śrubę napinania
łańcucha (3) na osłonie koła
łańcuchowego (6) w lewo, do
Summary of Contents for AKS 1820 T Lion-Set
