background image

21

GENERAL

Although all gas connections on the grill are leak 

tested at the factory prior to shipment, a complete gas 

tightness check must be performed at the installation 

site due to possible mishandling in shipment, or 

excessive pressure unknowingly being applied to the 

unit. Periodically check the whole system for leaks 

following the procedures listed below. If the smell of 

gas is detected at any time, you should immediately 

check the entire system for leaks.

BEFORE TESTING 

Make sure that all packing material is removed from 

the grill including the burner tie-down straps. 

DO NOT SMOKE WHILE LEAK TESTING. 

NEVER LEAK TEST WITH AN OPEN FLAME. 

Make a soap solution of one part liquid detergent and 

one part water. You will need a spray bottle, brush, or 

rag to apply the solution to the fittings. For the initial 

leak test, make sure the L.P. cylinder is full. 

TO TEST 

Make sure all control valves are in the “OFF” position. 

Turn the gas supply on. Check all connections from 

the L.P. cylinder up to and including the connection to 

the manifold pipe assembly (the pipe that goes to the 

burners). Use the soap solution and spray or brush it 

onto all of these connections. Soap bubbles will 

appear where a leak is present. If a leak is present, 

immediately turn off the gas supply, tighten any 

leaking fittings, turn gas on, and recheck. Should the 

gas continue to leak from any or all of the fittings, turn 

off the gas supply, and contact our customer service 

at

1-866-814-0585

Only those parts recommended by the manufacturer 

should be used on the grill. Substitution will void the 

warranty. Do not use the grill until all connections 

have been checked and do not leak. 

GAS FLOW CHECK 

Each grill burner is tested and adjusted at the factory prior 

to shipment; however, variations in the local gas supply 

may make it necessary to adjust the burners, the flames 

of the burners should be visually checked. 

Flames should be blue and stable with no yellow tips, 

excessive noise or lifting. If any of these conditions exist, 

check to see if the air shutter or burner ports are blocked 

by dirt, debris, spider webs, etc. If you have any questions 

regarding flame stability, please call customer service at 

1-866-814-0585

.

ALWAYS CHECK FOR LEAKS AFTER EVERY LP 

TANK CHANGE 

Check all gas supply fittings for leaks before each 

use. It is handy to keep a spray bottle of soapy water 

near the shut-off valve of the gas supply line. Spray 

all the fittings. Bubbles indicate leaks. 

Disconnected L.P. cylinders must have threaded valve 

plugs tightly installed, and must not be stored in a 

building, garage or any other enclosed area. 

LEAK TESTING 

Test leak burner connections where shown.

Ɣ0HWDOJDVKRVH
Ɣ+RVHFRQQHFWLRQWREXUQHULQOHWILWWLQJ
Ɣ0DLQJDVKRVHFRQQHFWLRQ

Summary of Contents for 143757





























Reviews: