manualshive.com logo in svg

Greystone Energy Systems GDT Series, Installation Instructions Manual

Share
Download
Greystone Energy Systems GDT Series Installation Instructions Manual Download Page 9

Page  9

Use <UP> or <DOWN> to scroll through the available options. 

The strobe alarm trip point for CO may be set to OFF or from 

20 to 500 ppm in 10 ppm increments. The default is 150 ppm. 

The strobe may operate as a CO alarm, a NO

2

 alarm or both 

depending on the trip point settings. If set to OFF, then the 

strobe will not operate as a CO alarm.

Strobe

Enable

Use <UP> or <DOWN> to enable or disable the Strobe LED. When disabled, the 

Strobe will not flash if the strobe trip point is exceeded. The strobe will still flash 

on startup and will still flash for a fault alarm (if enabled). The factory default is 

Enable.

<MENU> 

Press to advance to next menu item

9. STROBE

CO Strb

Trip 150

Only if the 

strobe

 is enabled and the 

CO sensor

 is installed

10. CO STROBE

TRIP

Use <UP> or <DOWN> to scroll through the available options. 

The CO strobe delay may be set from 0 to 10 minutes in 1 minute 

increments. The default is 5 minutes.

Use <UP> or <DOWN> to scroll through the available options. 

The NO2 strobe delay may be set from 0 to 10 minutes in 1 

minute increments. The default is 5 minutes.

Use <UP> or <DOWN> to scroll through the available options. 

The strobe alarm trip point for NO

2

 may be set to OFF or from 1 

to 10 ppm in 1 ppm increments. The default is 2 ppm. The strobe 

may operate as a CO alarm, a NO

2

 alarm or both depending 

on the trip point settings. If set to OFF, then the strobe will not 

operate as a NO2 alarm.

CO Strb

Dly 5Min

NO2 Strb

Dly 5Min

NO2 Strb

Trip 2

Only if the 

strobe

 is enabled, the 

CO sensor

 is installed and the 

CO Strb Trip

 is not set to 

OFF

Only if the 

strobe

 is enabled, the 

NO

2

 sensor

 is installed and the 

NO

2

 Strb Trip

 is not set to 

OFF

Only if the 

strobe

 is enabled, the 

NO

2

 sensor

 is installed

11. CO STROBE

DELAY

13. NO

2

 

STROBE DELAY

12. NO

2

 

STROBE TRIP

<MENU> 

Press to advance to next menu item

<MENU> 

Press to advance to next menu item

<MENU> 

Press to advance to next menu item

<MENU> 

Press to advance to next menu item

<MENU> 

Press to advance to next menu item

Alarm 1

CO

Press the <UP> or <DOWN> to scroll through the available 

options. The available options are CO or NO

2

. Alarm1 may be 

assigned to either sensor. The default is CO.

Only if 

Relay1

 installed & only if 

2 sensors

 are installed

15. ALARM 1

Use <UP> or <DOWN> to toggle the strobe ON or OFF. Press 

<MENU> to reset to OFF and advance.

Strobe

Test OFF

Only if the 

strobe

 is enabled

14. STROBE 

TEST

<MENU> 

Press to advance to next menu item

IN-GE-GDTXXX-06

Copyright © Greystone Energy Systems, Inc.   All Rights Reserved    Phone:  +1 506 853 3057  Web: www.greystoneenergy.com

Summary of Contents for GDT Series



















Reviews:

No comments

Brands by name

Popular brands

Load more brands