Greystone Energy Systems GDT Series Installation Instructions Manual Download

Page: 10 / 18

Page 10

Alarm 1

Trip 50

Alarm 1

Trip 2

Press the <UP> or <DOWN> to change the Alarm1 Setpoint

within the limits. If Alarm1 is assigned to CO the range is 20 to

500 ppm in 10 ppm increments and default is 50 ppm. If Alarm1

is assigned to NO2 the range is 1 to 10 ppm in 1 ppm increments

and default is 2 ppm.

Only if

Relay1

is installed

16. ALARM 1

SETPOINT

Alarm 1

Hyst 10

Alarm 1

Hyst 0.5

Press the <UP> or <DOWN> to change the Alarm1 Hysteresis

within the limits. If the Alarm1 is assigned to CO the range is

10 to 100 ppm in 5 ppm increments and default is 10 ppm. If

Alarm1 is assigned to NO

the range is 0.5 to 2.0 ppm in 0.5 ppm

increments. The default is 0.5 ppm.

17. ALARM 1

HYSTERESIS

Alarm 1

Dly 2Min

Relay 1

Direct

Relay 1

Test OFF

Press the <UP> or <DOWN> to change the Alarm1 Delay time

within the limits. The delay time may be set from 0 to 10 minutes

in 1-minute increments. The default is 2 minutes.

Press the <UP> or <DOWN> to toggle the available options.

Relay 1 operation may be set to Direct or Reverse. Direct

operation means the relay is normally not energized and will

energize on an alarm condition (the NO/NC PCB designations

are correct). Reverse operation means the relay is normally

energized and will de-energize on an alarm condition (the NO/

NC PCB designations are reversed). Reverse operation can be

used for ‘Fail Safe’ operation as the relay will change state on

power loss. The default is Direct.

Press the <UP> or <DOWN> to toggle Relay1 ON or OFF to test

the relay operation.

18. ALARM 1

DELAY

19. RELAY

OPERATION

20. RELAY TEST

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

Alarm 2

Press the <UP> or <DOWN> to scroll through the available

options. The available options are CO or NO

. Alarm 2 may be

assigned to either sensor. The default is CO.

Only if

Relay2 & 2 sensors

are installed

21. ALARM 2

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

Alarm 2

Trip 150

Alarm 2

Trip 4

Press the <UP> or <DOWN> to change the Alarm2 setpoint

within the limits. If Alarm2 is assigned to CO the range is 20

to 500 ppm in 10 ppm increments and default is 150 ppm. If

Alarm2 is assigned to NO

the range is 1 to 10 ppm in 1 ppm

increments. Default is 4 ppm.

22. ALARM 2

TRIP POINT

<MENU>

Press to advance to next menu item

IN-GE-GDTXXX-06

Summary of Contents for GDT Series



















Search results

Summary of Contents for GDT Series

Reviews:

Related manuals for GDT Series

Brands by name

Popular brands

Greystone Energy Systems GDT Series, Installation Instructions Manual

Search results

Summary of Contents for GDT Series

Reviews:

Related manuals for GDT Series

Brands by name

Popular brands