Greyline Instruments OCF 5.0 User Manual Download Page 37 | Manualshive

Page: 37 / 41

background image

Page 37

OCF 5.0 Open Channel Flow Monitor

POWER INPUT OPTION
9-32VDC

OCF 5.0 Level & Flow Monitors may be ordered factory-configured for 9-32VDC power input.

QUICK BENCH TEST:

Connect Sensor as shown below, then Power. When properly connected figures will show on the large
LCD display. Test operation of the OCF 5.0 by holding the sensor steadily and aiming at a flat, stable
target 12 to 28" (305 to 711 mm) away from the end of the sensor. Allow a few seconds for the OCF 5.0
to lock onto the target before displaying its distance. The OCF 5.0 will now display Range in ft or cm
(factory calibration).

CONNECTIONS:

POWER INPUT: Connect 9-32VDC/0.5 Amps to the + and - terminals. The Power Input GND must be
connected to the nearest Ground pole. A 1 amp fuse in line is recommended.

«
...
35
36
37
38
39
...
»

Summary of Contents for OCF 5.0










































Reviews:

No comments

Related manuals for OCF 5.0

Brand: Kawai Pages: 5

Brand: Jata hogar Pages: 12

Brand: Gazelle Pages: 2

Brand: Hardy Barth Pages: 27

Brand: IFM Pages: 2

Brand: jenway Pages: 18

VOLUTANK Petro 3003

Brand: Bartec Pages: 10

IRmadillo DOC1048R

Brand: Keit Pages: 27

Brand: Keeler Pages: 68

Brand: Reed Instruments Pages: 14

Ratio:Guard Advanced

Brand: H.E. Anderson Pages: 9

Arrow Mobile Android

Brand: MADDALENA Pages: 12

Brand: Omega Pages: 26

Brand: E Instruments Pages: 2

Panametrics XDP

Brand: Baker Hughes Pages: 64

Brand: IROX Pages: 8

Brand: Hammerhead Pages: 44

Brand: YOKOGAWA Pages: 169

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands