GREWIN PCLC-901D Manual Download Page 9

Page: 9 / 14

TIANJIN GREWIN TECHNOLOGY CO.,LTD.

Web:www.grewin-tech.com Wh86-13072088960
Email:[email protected]

Address:DongLi Distr Tianjin City, China

Tel:

+86-22-84943756

2.4.3 Scale operation

If need to check the waveform velocity details, and analysis the waveform, we could choose the scale operation to scale and check the details.

Chose the main menu Scale and to zoom in/out as shown in Fig.2.7

Steps:

Choose Scale menu,then choose Full extent, Zoom in or Zoom out

Full extent restore the complete waveform

Zoom out zoom out and display part of the waveform centered on dotted cursor. Move the dotted cursor to left/right and it will automatically

page turning when reach the border.

Zoom in zoom in and display part of the waveform centered on dotted cursor. Move the dotted cursor to left/right and it will automatically page

turning when reach the border.

2.4.4 Copy/both operation

If need to compare the waveform, it is suggested to use the the Copy/both button.The device could temporarily storage 3 waveform and display the

waveform in the Copy Window. Refer Fig. 2.8

*ICM (impulse current mode) doesn’t have this function

Sub-menu introduction:

zone 1 copy:Temporary storage the waveform in window 1 on the right.Other copy buttons are similar function.

zone 1 Both:Display the waveform of window 1 into the main window.Other both buttons are similar function.

Fig.2.7 Scale operation

Summary of Contents for PCLC-901D














