GREISINGER GMH 3451 Operating Manual Download Page 18

H72.0.11.6C-04 

 Operating Manual GMH 3451 

page 18 of 18 

 

 _____________________________________________________ 

_____________________________________________________________________________ 

 

18 Specification 

 
 

 

Measuring 
ranges 

Anzahl  

Conductivity 1 *)  0,0 ... 200,0 µS/cm  
          ”         2 *)  0 ... 2000 µS/cm      
          ”         3 *)  0,00 ... 20,00 mS/cm  
          ”         4 *)  0,0 ... 200,0 mS/cm  
          ”         5 *)  0 ... 400 mS/cm  
Resistivity 

0,005 ... 100,0 kOhm*cm  

TDS 

0,0 ... 1999 mg/l   

Salinity 

0,0 ... 70,0 g/kg (PSU) 

Temperature 

-5,0 ... +100,0 °C 
23,0 ... 212,0 °F 

Accuracy Conductivity ±0,5% 

v.MW ±0,3 % FS or ±2 µs/cm 

Temperature ±0,2 

Connections Conductivity/ 

Temperature 

Permanently connected measuring cell 

Interface 
Analogue output 

Serial interface (3.5mm jack) can be connected to USB or RS232 interface of a PC 
via electrically isolated interface adapter USB3100, USB 3100 N, GRS3100 or 
GRS3105 (see accessories). Alternative selectable analogue output 0-1V 

Measuring cell   

Four-electrode-conductivity-measuring cell with integrated temperature sensor 

Electrode material special graphite 
Shaft material 

epoxy 

Size 

dia. 12 mm, length 120 mm 

Ambient condition -5 … +80°C (continuous) up to +100°C (short-duration) 

Display 

 

4 digit 7-segment (main and secondary display) with additional symbols 

Additional functions 

Min / max / hold 

Adjustment/Calibration 

Cell correction manually or automatically via selectable reference solution  

Data logger 

Real-time clock 
Cyclic: 10000 data sets, cycle time selectable: 1s … 60 min 
Single: 1000 data sets (with measuring point input, 40 selectable measuring point 
texts or numbers) 

Alarm 

2 alarm channels with separate limit values for conductivity (or resistivity, TDS, SAL) 
and temperature  
Alerting: buzzer / visual / interface 

Housing  

Break-proof ABS housing 

Protection class 

Front side IP65 

Dimensions 
L*W*H [mm] 

142 x 71 x 26 mm 

(L x W x H)

 

Working conditions

 

-25 to 50 °C; 0 to 95 % RH (non condensing) 

Storage temperature 

-25 to 70 °C 

Power supply   

9V-battery, typ IEC 6F22 (included in scope of supply) or external 

Current 
consumption 

2 mA (Out = Off)

Battery indicator  Automatically if battery exhausted 

 and ’ bAt ’ 

Auto-Off-Function 

Device will be automatically switched off if no key is pressed/no interface 
communication takes place for the time of the power-off delay. The power-off delay 
can be set to values between 1and 120 min.; it can be completely deactivated. 

Directives and standards 

The instruments confirm to following European Directives: 
 2014/30/EU 

EMC 

Directive 

 2011/65/EU 

RoHS 

Applied harmonized standards: 
 

EN 61326-1 : 2013 

emissions level: class B 
emi immunity according to table 3 and A.1 
Additional fault: <1% 

Summary of Contents for GMH 3451



















Reviews: