H40.0.01.6C-09
Operating Manual GMH 3330
Page 8 of 16
’AVG’: Selection of Averaging Proceedings for Flow
Measurement
(only STS005/020)
Cont:
continuous averaging
- the average value calculated from
the measurements conducted during the averaging period will be
displayed.
Hold:
press key for averaging
- flow measurements will be taken during
the averaging period, then the average value will be calculated and
displayed till the next flow measurement is started.
’t.AVG’: Setting of Averaging Period
(only STS005/020)
1..30:
Time for averaging (in seconds) during flow measuring
’Unit’: Selection of Temperature Unit
°C:
All temperature values in degrees Celsius
°F:
All temperature values in degrees Fahrenheit
’Offset T1’: Zero Displacement of Sensor Tempera-
ture T1
(only TFS0100)
-10.0°C...10.0°C
or
-18.0°F...18.0°F:
The zero point of the measurement of T1 will be
displaced by this value.
off:
Zero point displacement is deactivated (=0.0°)
’Offset T2’: Zero Displacement of Temperature T2
-10.0°C...10.0°C
bzw.
-18.0°F...18.0°F:
The zero point of the measurement of T2 will be
displaced by this value.
off:
Zero point displacement is deactivated (=0.0°)
’Corr’: Selection of Display Correction Factor
1.001...1.200:
The temperature value (referring to 0°C or. 32°F) will be
multiplied by this factor.
off:
Factor is deactivated (=1.000)
’Power.off’: Selection of Power-Off Delay
1...120
:
Power-off delay in minutes. Device will be automatically
switched off as soon as this time has elapsed if no key is
pressed/no interface communication takes place. (automati-
cally deactivated for cyclic loggers)
off:
automatic power-off function deactivated
(continuous operation, e.g. in case of mains operation)
’Address’: Selection of Base Address
01, 11,
21, …, 91:
Base address for interface communication. Channel
1 will be addressed by the set base address, chan-
nel 2 to 6 will have the following addresses.
(Example: base address 21 - channel 1 = 21, chan-
nel 2 = 22, ..., channel 6 = 26)
Using the interface converter GRS3105 it is possible to connect several devices to a single interface. As
a precondition the base addresses of all devices must not be identical. In case several devices are con-
nected via one interface make sure to configurate the base addresses accordingly.
r.H.
T d
T 2
T d
m/s
kJ/kg
AL
L o g g
T 1
Co rr
CAL
max
min
2
5
r.H.
T d
T 2
T d
m/s
kJ/kg
AL
L o g g
T 1
Co rr
CAL
max
min
2
5
°C
r.H.
T d
T 2
T d
m/s
kJ/kg
AL
L o g g
T 1
Co rr
CAL
max
min
2
5
°C
r.H.
T d
T 2
T d
m/s
kJ/kg
AL
L o g g
T 1
Co rr
CAL
max
min
2
5
°C
r.H.
T d
T 2
T d
m/s
kJ/kg
AL
L o g g
T 1
Co rr
CAL
max
min
2
5
r.H.
T d
T 2
T d
m/s
kJ/kg
AL
L o g g
T 1
Co rr
CAL
max
min
2
5
r.H.
T d
T 2
T d
m/s
kJ/kg
AL
L o g g
T 1
Co rr
CAL
max
min
2
5
r.H.
Td
T2
Td
m/s
kJ/kg
AL
Logg
T1
Corr
CAL
max
min
2
5
