background image

2. Push the battery pack into the battery compartment

until the battery pack locks into place.

3. When you hear a click, the battery pack is installed.

3.7

REMOVE THE BATTERY PACK

Figure 5

1. Push and hold the battery release button.
2. Remove the battery pack from the machine.

4

OPERATION

 

NOTE

Remove the battery pack and keep hands clear of the

lock out button when you move the machine.

 

IMPORTANT

Examine the chain tension before each use.

4.1

EXAMINE THE CHAIN

LUBRICATION

 

NOTE

Do not use the machine without sufficient chain

lubrication.

Figure 6

1. Examine the lubricant level of the machine from the

oil indicator.

2. Add the lubricant if it is necessary.

4.2

START THE MACHINE

Figure 7

1. Pull the lock-out button with your thumb backward.
2. Press the trigger at the same time.

4.3

STOP THE MACHINE

Figure 7.

1. Release the trigger to stop the machine.

4.4

DELIMBING A TREE

Figure 8

 

WARNING

Make sure that there is nothing or nobody in the area

where the branches fall.

• Stand opposite the branch you will cut.
• Start to cut the higher branches.
• Then cut the lower branches.
• Cut downwards to prevent the bar from jamming.

4.5

LIMB TREE BRANCHES

Limbing is to remove the branches from a fallen tree.

Figure 9

1. Keep the larger lower branches to hold the log off

the ground.

2. Remove the small limbs in one cut.
3. Limb the branches with tension from the bottom to

up.

4. Keep the larger lower branches as a support until

the log is limbed.

5

MAINTENANCE

 

CAUTION

Do not let brake fluids, gasoline, petroleum-based

materials touch the plastic parts. Chemicals can cause

damage to the plastic, and make the plastic

unserviceable.

 

CAUTION

Do not use strong solvents or detergents on the plastic

housing or components.

 

WARNING

Remove the battery pack from the machine before

maintenance.

5.1

ASSEMBLE THE GUIDE BAR AND

THE CHAIN

Figure 10-14

1. Remove the battery pack from the machine.
2. Loose the chain cover by turning the chain cover

knob counterclockwise.

3. Remove the chain cover.
4. Put the chain drive links into the bar groove.
5. Put the chain cutters in the direction of the chain

operation.

6. Put the chain in position and make sure that the

loop is behind the guide bar.

7. Hold the chain and bar.
8. Put the chain loop around the sprocket.
9. Make sure the chain tension pin hole on the guide

bar fits correctly with the bolt.

10. Install the chain cover.
11. Tighten the chain. Refer to 

Adjust the chain tension.

12. Tighten the chain cover knob when the chain is well

tensioned.

6

English

EN

Summary of Contents for PSG301






















Reviews: