background image

6

TRANSPORTATION AND

STORAGE

Before you move the machine, always
• Remove the battery pack from the machine.
• Keep hands clear of the lock-out button.
• Put the scabbard on the guide bar and the chain.
Before you put the machine into storage, always
• Remove all residual oil from the machine.
• Remove the battery pack from the machine.
• Clean all unwanted material from the machine.
• Make sure that the storage area is

• Not available to children.
• Away from agents which can cause corrosion,

such as garden chemicals and de-icing salts.

7

TROUBLESHOOTING

Problem

Possible cause

Solution

The machine

does not start

The poles are

not assembled

correctly.

Assemble the

poles according

to the instruc-

tions.

The lock-out

button and trig-

ger are not de-

pressed at the

same time.

1. Push and

hold the

lock-out but-

ton

2. While you

hold the

lock-out but-

ton, pull the

trigger.

3. Release the

lock-out but-

ton to start

the machine.

Problem

Possible cause

Solution

The bar and

chain gets hot

and smokes.

Oil tank is emp-

ty.

Fill the oil tank.

The discharge

port is blocked.

1. Remove the

battery pack.

2. Remove dirt

from the dis-

charge port.

Inlet opening of

inner oil tank is

blocked.

1. Clean the oil

tank.

2. Fill with

clean bar

and chain lu-

bricant.

The sprocket is

stuck and clog-

ged with debris.

1. Clean the

sprocket.

2. Fill with

clean bar

and chain lu-

bricant.

The bar and

chain gets too

hot and can not

cut.

The chain ten-

sion is too tight

or too loose.

Refer to Adjust

the Chain Ten-

sion in the man-

ual.

The chain is dull Sharpen or re-

place the chain.

The chain is put

on backwards.

Take out the

chain and turn it

in the right direc-

tion.

The motor runs,

but the chain

does not cut cor-

rectly, or the

motor stops af-

ter around 3

seconds.

When you use

the machine un-

der load, it

stops.

1. Release the

trigger.

2. Start the ma-

chine again.

The chain is not

lubricated.

Lubricate the

chain to de-

crease the fric-

tion.

8

TECHNICAL DATA

Voltage

24V DC

No load speed

3 450 /min

Guide bar length

203 mm

Chain stop

< 2 s

Chain oil capacity

50 ml

Weight (without battery

pack)

3.2 kg

Measured sound pres-

sure level

L

pA

= 88dB(A), K

pA

= 3

dB(A)

8

English

EN

Summary of Contents for PSG301






















Reviews: