background image

(1) This device may not cause harmful interference,and 

(2) This device must accept any interference received, including interference that may cause undesired operation. 

2. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority 

to operate the equipment. 

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of 

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 
• Reorient or relocate the receiving antenna. 

• Increase the separation between the equipment and receiver. 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

• Consult the dealer or an experienced radio/TV technician for help. 

FCC Radiation Exposure Statement 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should 

be installed and operated with minimum distance 20cm between the radiator & your body. 

7

English

EN

Summary of Contents for GRV-5011






























Reviews: