GreenWorks 00-0000-0 Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 42

background image

29

MAINTENANCE

•

Release the tip of the guide bar, and turn the chain tensioning knob 1/2 turn clockwise.

•

Hold the tip of the guide bar up and tighten the chain cover lock knob.

The chain is correctly tensioned when there is no sag on the underside of the guide bar, and
when the chain is snug, but can be turned by hand without binding.

NOTE: If chain is too tight, it will not rotate. Loosen the chain cover lock knob slightly, and turn the chain
tensioning knob 1/4 turn counter-clockwise. Lift the tip of the guide bar up, and retighten the chain cover lock
knob. Ensure that the chain will rotate without binding. 30

«
...
27
28
29
30
31
...
»

Summary of Contents for 00-0000-0











































Reviews:

No comments

Related manuals for 00-0000-0

Brand: Draper Pages: 10

Brand: Blaupunkt Pages: 166

Brand: Raider Pages: 90

Brand: ayerbe Pages: 48

Brand: Makita Pages: 156

Brand: McCulloch Pages: 24

Brand: McCulloch Pages: 620

Brand: Dolmar Pages: 24

Brand: Jonsered Pages: 20

Brand: Jonsered Pages: 36

Brand: Maruyama Pages: 42

Brand: Lux Tools Pages: 244

Brand: Talon Tools Pages: 6

M18 Fuel 2727-20

Brand: Milwaukee Pages: 48

Brand: Echo Pages: 92

Brand: Echo Pages: 36

Brand: Okay Pages: 52

Brand: Electrolux Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands