manualshive.com logo in svg

Greenlee CCCX, Instruction Manual, Page: 8 / 26

Share
Download
Greenlee CCCX Instruction Manual Download Page 8

Greenlee / A Textron Company

8

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

CCCX and CCCXC Tools

Operation (cont’d)

Crimping

Setup

1.

Open the tool head.

2.

Remove any accessories from the tool head.

3.

Select the appropriate set of dies. Use the
table provided on this page to select the
corresponding adapter set.

4.

Install the adapters and dies—one set in each
groove. If either the adapters or dies have W-type
tabs, lock them in place with the W-type detents.

Important: W-type dies must be locked into place
or the die detents will be damaged.

5.

Visually check the dies to ensure that they are
aligned correctly so that they will complete the
crimping operation.

6.

Close the tool head.

Dies

Adapter Set

Greenlee K22, KA22, KC22-type

UA22

Greenlee W-type

UAW

Kearney “OD”

UAK

Thomas & Betts “6TON”

UAK

D

3

 Profile

UAW

Blackburn

®

 “O”

UAK

Huskie “HT”

UAK

FCI Burndy “W”

UAW

Huskie “HT-58”

UAW

Ilsco “ND-60”

UAW

Izumi “N58”

UAW

Panduit “CD-2001”

UAW

Accessory Table

W-type

W-type Detents: Press 
and slide the adapter 
and/or die into place. 
Release to lock.

K22-type

Kearney

Important: 

W-type dies 

must be locked into 
place or the die detents 
will be damaged.

Summary of Contents for CCCX



























Reviews:

No comments