manualshive.com logo in svg

Greenlee CCCX, Instruction Manual, Page: 10 / 26

Share
Download
Greenlee CCCX Instruction Manual Download Page 10

Greenlee / A Textron Company

10

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

CCCX and CCCXC Tools

Operation (cont’d)

Cutting

Wear eye protection when operating
or servicing this tool.

Failure to wear eye protection could
result in serious eye injury from
flying debris or hydraulic oil.

Electric shock hazard:

This tool is not insulated. When using
this unit as a cable cutter on or near
energized electrical lines, use proper
personal protective equipment.

Failure to observe this warning could
result in severe injury or death.

Setup

1.

Open the tool head.

2.

Remove any accessories from the tool head.

3.

Select the appropriate set of blades, using the
table provided on this page.

4.

Install one blade in each groove. If the blades have
W-type tabs, lock them in place with the W-type
detents.

Important: W-type dies must be locked into place
or the die detents will be damaged.

5.

Visually check the blades to ensure that they are
aligned correctly so that they will complete the
butting operation.

6.

Close the tool head.

Setup for Din Rail Cutters

1.

Install both blades in the movable head.

2.

Close the head.

3.

Slide one blade over until it engages in the W-type
detents.

Cutting Procedure

1.

Press the latch and open the tool head.

2.

Position the item to be cut in the tool head.

3.

Close the tool head.

4.

Pull the trigger to cut the item.

5.

Release the trigger when the cut is complete.

6.

The ram returns automatically.

Accessory Table

Task

Blade

Copper and aluminum

UC26

26 mm (1.00") max.

Copper and aluminum

UC40

40 mm (1.56") max.

ACSR
Copperweld
ACAR
Guy strand
EHS guy strand

UCACSR

Ground rod
Anchor rod
Soft bolts
Rebar

Threaded rod

Threaded rod

DIN rail

DIN rail

W-type Detents:
Press and slide the
adapter and/or die 
into place. 
Release to lock.

Important: 

W-type dies must be locked into

place or the die detents will be damaged.

Summary of Contents for CCCX



























Reviews:

No comments