background image

4.3 ANALOG OUTPUT SIGNALS

Airflow:

  Available on connector J1, terminals AO1+ and AO1- or AO2+ and AO2-. The full scale output is equal to 

Max flow as inputted into the Vari-Green transmitter on the Flow Configuration submenu.

Temperature:

 Available on connector J1, terminals AO1+ and AO1- or AO2+ and AO2-. The temperature analog 

output has a fixed scale of -20º F to 140º F.

SECTION 5.0: Maintenance / Inspections / 
Troubleshooting

5.1 MAINTENANCE / INSPECTIONS

The Vari-Green

 system h

as been designed to operate in most HVAC applications without the need 

for periodic maintenance or calibration. In some applications, it may be necessary to perform a visual 
inspection of the probe and sensors, and if necessary clean them using a soft, small brush and/or 
compressed air to remove any accumulated particulate or debris. 

5.2 TROUBLESHOOTING

The Vari-Green

 system is i

ntended to provide long-term, trouble-free operation. In the event there is an 

issue with the Vari-Green measurement system, or the BMS or the controller ceases to receive valid 
airflow and/or temperature signals, make certain the following have been checked and confirmed:
•  The power wiring is securely connected to the proper terminals and is providing the intended 24V AC/

DC power.

• The signal wiring is securely connected to the proper terminals.
•  The probe-to-probe and probe-to-transmitter cables and connections are properly connected and 

secure.

• Power cycles the transmitter.
If after following the above troubleshooting steps, the Vari-Green system continues to operate improperly, 
contact Greenheck for technical assistance.

Technical Support:

E-mail: [email protected] or

Phone: 1-800-717-6540

482599 • Vari-Green® Transmitter IOM, Rev. 3, October 2018 

Copyright 2018 © Greenheck Fan Corporation

10

As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications 
without notice.

Product warranties can be found online at Greenheck.com, either on the specific product page or in the literature 
section of the website at Greenheck.com/Resources/Library/Literature.

®

Phone: 715.359.6171 • Fax: 715.355.2399 • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com

Our Commitment

Summary of Contents for AMD-TD Series











Reviews: