background image

Object Processing

Object Type

Optional Properties

Writeable Properties

Analog Input

Description

Analog Output

Description

Present_Value

Analog Value

Description

Present_Value

Binary Input

Description
Active_Text
Inactive Text

Binary Output

Description
Active_Text
Inactive_Text
Relinquish_Default1)
Priority_Array1)

Present_Value

Binary Value

Description
Active_Text
Inactive_Text
Relinquish_Default1)
Priority_Array1)

Present_Value

Device

Description
Location

Object_Identifier
Object_Name
Location
APDU_Timeout
Number_Of_APDU_Retries
Max_Master 2)
Max_Info_Frames2)

Multistate Input

Description
State_Text

Multistate Value

Description
State_Text
Relinquish_Default1)
Priority_Array1)

Present_Value

Multistate Output

Description
State_Text
Relinquish_Default1)
Priority_Array1)

Present_Value

•  The properties Object_Name and Location of the Device Object support up to 255 characters (all other character 

strings are read-only).

• The device does not support the CreateObject and DeleteObject service.

Service Processing

• The device supports DeviceCommunicationControl service. No password is required.

1) Only if object is commandable.
2) Only if MS/TP is the selected data link layer type

AMD-xx-TD Series

9

Summary of Contents for AMD TD Series













Reviews: