background image

This manual is the property of the owner and is required for future maintenance. Please leave it with the owner when 
the job is complete.

Receiving and Handling

Upon receiving dampers, check for both obvious 
and hidden damage. If damage is found, record all 
necessary information on the bill of lading and file 
a claim with the final carrier. Check to be sure that 
all parts of the shipment, including accessories, are 
accounted for. 
Dampers must be kept dry and clean. Indoor storage 
and protection from dirt, dust, and the weather is 
ideal. Do not store at temperatures in excess of  
100°F (37°C).

Table of Contents

General Information  ................................................ 1

Receiving and Handling  ......................................... 1

Pre-Installation Guidelines ...................................... 2

Electrical Guidelines  ............................................... 2

Installation  .........................................................3-10

Setup & Operation for AMD-xx-TD Series 

Dampers  ................................................................. 3

AMD-xx-TD Series without a Factory Supplied 
Controller  ................................................................ 4

AMD-xx-TD Series Ordered with a Factory Supplied 
Actuator  ...............................................................4-5

  Analog Factory Supplied Controller  ..................... 4

  BACnet Enabled Factory Supplied Controller ...... 5

Setting the Actuator/Controller’s BACnet 
Configuration  .......................................................6-9

Optimal Placement for AMD-xx-TD  ................10-11

Minimum Installation Requirements  ..................... 12

Maintenance  ......................................................... 12

Warranty  ............................................................... 12

Our Commitment  .................................................. 12

®

AMD-xx-TD Series

1

Document 478799

AMD-xx-TD Series

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install, 
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure 
to comply with these instructions will result in voiding of the product warranty and may result in personal injury 
and/or property damage.

Summary of Contents for AMD TD Series













Reviews: