background image

*

★ 

24℃

-

27℃

43

21℃

18℃

Notices for operation

Working principle and special functions for cooling

Principle:

Air conditioner absorbs heat in the room and transmit to outdoor and discharged,
so that indoor ambient temperature decreased, its cooling capacity will increase

or decrease by outdoor ambient temperature.

Anti-freezing function

If the unit is running in COOL mode and in low termperature, there will be frost formed

on the heat exchanger, when indoor heat exchanger temperature decreased below 0

,

the indoor unit microcomputer will stop compressor running and protect the unit.

Working principle and special functions for heating

Principle:

The unit absoebs heat from outdoor air,carrys and emits the

 

heat in indoors

to make indoor air temperature higher. Its heating capacity would be lower

according to the low weather of outdoor ambient. 

This heating air circulation system can enhance the indoor temperature

in a short while.

If outdoor temperature got lower, please operate with the other heating ventilating

equipments.

Defrosting:

When outdoor temperature is low but with high humidity, after a long while running,

frost will form on outdoor unit, that will affect the heating effect, at this time,

the auto defrosting function will act, the heat running will stop for 8-10mins.

During the auto defrost, the fan motors of indoor unit and outdoor unit will stop.

During the defrost, the indoor indicator flashes, the outdoor unit may emit  vapor.

This is due to the defrosting, it isn't malfunction.

After defrost finished,the heating will recover automatically.

Anti-freezing function:

In "HEAT" mode, under the following three states, if indoor heat exchanger didn't reach certain

temperature, indoor fan would not opera

t

e to prevent blowing out cool air:

(Within 3mins)

1.Heating starts. 2.Af

t

er Auto defrosting finished. 3.Heating under the low temperature.

The conditions of unit can't normally run

The following temperature range protection device may act, that may cause stop running.

"HEAT"

running

Under the relative humidity above 80%( doors and windows opened) when cooling or dehu-

midifying for a long time, there will be dew drip off near the air vent.

"COOL"

running

"DRY"

running

Outdoor temp above

Outdoor temp below

Indoor temp. above

Outdoor temp above

Indoor temp. below

Indoor temp. below

Summary of Contents for GWCN1407X2B8NK1BA



























Reviews: