Gree GWC09ACC-K6DNA1C/I, Owner'S Manual

Page: 21 / 32

16
●
●
TIMER ON button
"TIMER ON" button can set the time for timer
on. After pressing this button, " " icon disap -
pears and the word "ON" on remote controller
blinks. Press "▲" or "▼" button to adjust TIMER
ON setting. After each pressing "▲" or "▼"
button. TIMER ON setting will increase or
decrease 1min. Holding "▲" or "▼" button, 2s
later, the time will change quickly until reaching
your required time.
Press "TIMER ON" to confirm it. The word "ON"
will stop blinking. " " icon resumes displaying.
Cancel TIMER ON: Under the condition that
TIMER ON is started up, press "TIMER ON"
button to cancel it.
TIMER OFF button
"TIMER OFF" button can set the time for timer
off. After pressing this button, " "icon disap -
pears and the word "OFF" on remote controller
blinks. Press "▲" or "▼" button to adjust TIMER
OFF setting. After each pressing "▲" or "▼"
button, TIMER OFF setting will increase or
decrease 1min. Holding "▲" or "▼" button, 2s
later, the time will change quickly until reaching
your required time.
Press "TIMER OFF" and the word "OFF" will
stop blinking. " " icon resumes displaying.
Under the condition that TIMER OFF is started
up, press "TIMER OFF" button to cancel it.
button /
temperature according to the detected tempera -
ture. Press this button again to close I FEEL func -
tion and " " will disappear.
Please put the remote controller near user when this
function is set. Do not put the remote controller
near the object of high temperature or low tem -
perature in order to avoid detecting inaccurate
ambient temperature. When I FEEL function is
turned on, the remote controller should be put
within the area where indoor unit can receive the
signal sent by the remote controller.
button
Press this button to start I FEEL function and " "
will be displayed on the remote controller. After
this function is set, the remote controller will send
the detected ambient temperature to the controller
and the unit will automatically adjust the indoor
temperature increased 2 , then the unit will run
at this setting temperature; In Heat mode: sleep
status after run for one hour, the setting tem -
perature will decrease 1 , two hours, setting
●
●
●
temperature will decrease 2 , then the unit will
run at this setting temperature.
Sleep 2 is sleep mode 2, that is air conditioner
will run according to the presetting a group of
sleep temperature curve.
Sleep 3-the sleep curve setting under Sleep
mode by DIY;
(1) Under Sleep 3 mode, press “Turbo” button
for a long time, remote controller enters into user
individuation sleep setting status, at this time,
the time of remote controller will display “ 1hour ”,
the setting temperature “88” will display the
corresponding temperature of last setting sleep
curve and blink (The first entering will display
according to the initial curve setting value of
original factory);
(2) Adjust "▲" and " ▼" button, could change
the corresponding setting temperature, after
adjusted, press “Turbo” button for confirmation;
(3) At this time, 1hour will be automatically
increased at the timer position on the remote
control, (that are "2hours" or "3hours" or "8
hours " ), the place of setting temperature " 88"
will display the corresponding temperature of
last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation,
until 8 hours temperature setting finished,
sleep,curve setting finished, at this time, the
remote controller will resume the original timer
display; temperature display will resume to origi -
nal setting temperature.
Sleep 3-the sleep curve setting under Sleep
mode by DIY could be inquired:
The user could accord to sleep curve setting
method to inquire the presetting sleep curve,
enter into user individuation sleep setting status,
but do not change the temperature, press
“Turbo” button directly for confirmation. Note: In
the above presetting or enquiry procedure, if
continuously within 10s, there is no button
pressed, the sleep curve setting within 10s,
there is no button pressed, the sleep curve
setting status will be automatically quit and
resume to display the original displaying. In the
presetting or enquiry procedure, press "ON/OFF"
button, " Mode " button, " Slee p " button, the
sleep curve setting or enquiry status will quit
similarly.