background image

Water-cooled Heat Recovery DC Inverter VRF 

53 

Error Code 

Content 

Error Code 

Content 

AU 

Long-distance emergency stop. 

nJ 

High temperature prevention when 
heating. 

Ab 

Emergency stop of operation. 

nU 

Eliminate the long-distance shielding 
command of IDU. 

Ad 

Limit operation. 

nb 

Bar code inquiry. 

An 

Child lock status. 

nn 

Length modification of connection 
pipe of ODU. 

  For detailed malfunction and maintenance, please refer to the engineering debugging 

and after-sales maintenance manual. 

8 Maintenance and Care 

Regular checking, Maintenance and care should be performed every six months by professional 

personnel, which will prolong the unit life span.  Disconnect the power supply before cleaning and 

maintenance. 

8.1 Outdoor Heat Exchanger 

After long-term running, accumulation of calcium oxide or other mineral sediments can be found 

on the heat transfer surface on the water side of the outdoor unit's heat exchanger. The scale 

formation of these minerals may affect the heat transfer performance and lead to higher air discharge 

pressure and more electrical energy consumption, as well as chilled water freezing due to reduced 

flow. To maintain the outdoor heat exchanger, do as follows:   

(1)  Check the water system on a regular basis, including water quality inspection, filter cleaning, 

confirmation of inlet and outlet water temperature difference and the check of water 

pressure.   

(2)  To clean the outdoor heat exchanger, use 5% dilute phosphoric acid, citric acid or other 

weak acid as the detergent. Highly corrosive strong acid cannot be adopted.   

(3)  Inject the 50~60

(122~140

)  detergent in the opposite direction of the normal flow. Set 

the flow rate 1.5 times of the normal one and keep the circulation for 2~5 hours.   

(4)  Discharge the detergent from the outdoor heat exchanger. Then, inject 1~2% sodium 

hydroxide or sodium bicarbonate water solution and circulate for 20~30 minutes to 

neutralize the acid of the detergent.   

(5)  After neutralization, use clean water to clean the outdoor heat exchanger. 

 

Fig.8.1.1 

 

Summary of Contents for GMV-WQ120WM/A-F



























































Reviews: