background image

 

 

To Users 

Thank you for selecting Gree’s product. Please read this instruction manual carefully before 

installing and using the product, so as to master and correctly use the product. In order to guide 

you  to  correctly  install  and  use  our  product  and  achieve  expected  operating  effect,  we  hereby 

instruct as below: 

(1)  This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they 

have been given supervision or instruction concerning use of the appliance by a person 

responsibility for their safety. Children should be supervised to ensure that they do not 

play with the appliance. 

(2)  In  order  to  ensure  reliability  of  product,  the  product  may  consume  some  power  under 

stand-by  status  for  maintaining  normal  communication  of  system  and  preheating 

refrigerant and lubricant. If the product is not to be used for long, cut off the power supply; 

please energize and preheat the unit in advance before reusing it. 

(3)  Please properly select the model according to actual using environment, otherwise it may 

impact the using convenience. 

(4)  This  product has gone  through strict  inspection  and  operational  test  before  leaving  the 

factory. In order to avoid damage due to improper disassembly and inspection, which may 

impact the normal operation of unit, please do not disassemble the unit by yourself. You 

can contact with the special maintenance center of our company if necessary. 

(5)  For personal injury or property loss and damage caused by improper operation such as 

improper  installation  and  debugging,  unnecessary  maintenance,  violation  of  related 

national laws and rules and industrial standard, and violation of this instruction manual, 

etc., we will bear no liability. 

(6)  When the product is faulted and cannot be operated, please contact with our maintenance 

center as soon as possible by providing the following information. 

1) Contents  of  nameplate  of  product  (model,  cooling/heating  capacity,  product  No.,  ex-

factory date). 

2) Malfunction status (specify the situations before and after the error occurs). 

(7)  All  the  illustrations  and  information  in  the  instruction  manual  are  only  for  reference.  In 

order  to  make  the  product  better,  we  will  continuously  conduct  improvement  and 

innovation. We have the right to make necessary revision to the product from time to time 

due  to  the  reason  of  sales  or  production,  and  reserve  the  right  to  revise  the  contents 

without further notice. 

(8)  The final right to interpret for this instruction manual belongs to Gree Electric Appliances 

Inc. of Zhuhai. 

 

 

 

Summary of Contents for GMV ND50PHS/B-T


























Reviews: