background image

YP1225A and YP1625A

Table of Contents

Index

Volumetric Seeding

Great Plains |

 

401-625B | 6/19/19

95

Calibration

You need a light weight container for each row sampled,

and a scale that is accurate at the expected sample
weight.

Great Plains recommends using enough rows and/or

revolutions to generate a sample of about 10 pounds

(4.5 kg), ideally:

Use at least two rows.

Use no fewer than 5 meter revolutions.

1. Set the seed inlet shutters to 2 (see planter

Operator’s Manual for details).

2. Select the section and rows to be sampled.
3. Use the clutches to disconnect the other sections of

the planter.
If the planter is equipped with Swath Command™,

disable all but the tested rows.

4. Raise the planter, and install the lift cylinder transport

locks. Leave tractor hydraulic system active.

5. Bring the hydraulic fan up to planting speed (see

planter Operator’s Manual for details).

6. Press the Fill Disk key and then the Row Fill key.

This diverts all split air to seed delivery. Remain in

this mode until no more seed is flowing to meters.

Press the Work Screen key to return to the main

work menu.

7. Press the Control Setup key and then the

Channel Setup key.

8. Press the Spreader Calibration key.
9. Engage the hydraulic drive circuit.
10. Press the Fill Disk key. This turns the meters one

revolution to fill the disk cells.

11. Determine the meter revolutions needed. The

following equation gives the number of meter

revolutions needed to meter 10 pounds. The tables

on page 96 provides approximate pounds (and kg)
per revolution of each wheel and seed.

12. Configure the seed monitor for the planter and crop

(material). If the seed density is not known, use 1

pound/cubic-foot or 1 lb/bu.

13. Consult the rate chart for the crop (page 96). Note

the allowed Meter RPM range for the intended seed
disk and planting speed.

14. Place a collection bucket under each test meter’s

seed tube.

Moving Chain Hazard:

Shafts turn and chains move as soon as the Start key is pressed

on the seed monitor. Set up collection containers so that they
may be unattended. Keep all persons clear of the planter while

calibrating.

15. In the Spreader Constant Calibration screen, enter

the # Meter Revs and press the Start key.

16. Weigh the containers plus seed (

GrossWeight

).

Subtract the empty container weights to obtain the
net weight.

17. The seed monitor assumes that all rows were tested.

If you tested fewer (commonly the case), scale the
sample size to planter-wide:

18. Enter the Amount Dispensed. The seed monitor

computes a new Spreader Constant.

NOTE:

If the net weight of the metered sampled was dramatically
different than expected, run another calibration to validate

or revise the new spreader constant.

19. Perform a Ground Speed Calibration procedure.
20. Refer to 

Furrow Checking Rate

” on page 91 to

verify seed rates.

Example: 

4 containers each weighing 8 oz.

8 oz x 4 = 32 oz

ContainerWeight

 at step 16 is 2 lbs

Example: 

planter model with 15 inch rows

crop: Hard Red Winter wheat

PoundsPerRev

0.04

RowsSampled

: 4

10 / (4 x 0.04) = 62.5

Enter 63 for “# Meter Revs” at step 15.

#MeterRevs

10

RowsSampled PoundsPerRev

---------------------------------------------------------------------------

=

Example: 

target population: 110 lbs/ac

desired speed: 5 mph

METER RPM: 12 rpm minimum, 45 rpm maximum

Example

ContainerWeight:

 2 lbs

GrossWeight

: 12.88 lbs

12.88 - 2 = 10.88

NetWeight

: 10.88 lbs

Example: 

NetWeight:

 10.88 lbs

RowCount

: 31

RowsSampled:

 4

(10.88 x 31) / 4 = 84.34

AmountDispensed

: 84.34

NetWeight

GrossWeight ContainerWeight

=

AmountDispensed

NetWeight RowCount

RowsSampled

--------------------------------------------------------

=

Summary of Contents for YP1225A

















































































































Reviews: