manualshive.com logo in svg

GREAT PLAINS Ultra-Till I 3030 Series, Operator'S Manual

Share
Download
GREAT PLAINS Ultra-Till I 3030 Series Operator'S Manual Download Page 22

Great Plains

 | 576-026M-A | 05/11/2021

Table of Contents

Index

20

UT3030-UT5052

Table of Contents

Index

Operating Instructions

Hydraulic Down Pressure 5 Section

Refer to Figure 10

This setup procedure is for tractors with closed-center

or  pressure  compensated  flow  hydraulic  systems.

Open center hydraulics not supported. Adjust down

pressure valve as shown on decal (1) (located on top

of inside and outside pressure reducing valve) 

Refer

to Figure 11

.

21. Close front valve (2) (clockwise); open one turn.
22. Set tractor flow rate for fold system to SLOW.
23. Engage hydraulics (continuous flow) down.
24. Adjust rear valve (3) to obtain 1200 psi.
25. Adjust front valve (4) to 1100 psi; lock valve.

26. Adjust  rear  valve  to  desired  down  pressure

(400-700 

psi 

inside 

wings-left 

valve 

(3))

(400-700 psi outer wings-right valve (4)). 

27. If the wings run high during operation, increase pressure.

If the center runs high, decrease pressure. Do not exceed

exceed 1000 psi.

Caution: This  machine  is  designed  for  continuous  hydraulic

flow to the wing fold cylinders during field operations. It is for

use on tractors having CLOSED CENTER hydraulics only. If

your  tractor  has  OPEN  CENTER  hydraulics,  please  consult

your dealer for operating instructions.

2

3

1

4

Figure 10

Down Pressure 5 Section

43178

Figure 11

Down Pressure Decal 5-Section

838-982C

Summary of Contents for Ultra-Till I 3030 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands