manualshive.com logo in svg

GREAT PLAINS NTA2007HD, Operator'S Manual

Share
Download
GREAT PLAINS NTA2007HD Operator'S Manual Download Page 133

Great Plains Manufacturing, Inc.

Contents

Index

Maintenance and Lubrication

129

04/09/2019

Contents

Index

166-283M

Brake Drum Maintenance

Refer to Figure 125

46. Inspect the shoe surface (the inside rim). Normal 

appearance is dull gray, with no more than light scor-

ing and light wear.

One or two light score marks are not cause for resur-

facing or replacement. If there are any questions 

concerning the condition of a drum, consult an 

expert.

Replace or resurface a drum that is heavily scored, 

worn to more than 0.51mm (0.020in) oversize, or 

has 0.38mm (0.015in) or greater run-out.

Brake Drum Resurfacing

47. A standard drum lathe is suitable for machining the 

shoe surface.

When removing surface, do not exceed the maxi-

mum diameter cast in the brake drum.

48. Be sure to remove any metallic chips and contamina-

tion resulting from drum machining.

Re-Mount Hub and Drum

Refer to Figure 126

49. Repack any bearings removed.
50. If replacing inner bearing seal

, orient it with the 

seam side out (away from bearing). Seat the seal so 

that it is completely inside the narrow diameter of the 

hub, and close to, but not touching the bearing 

cup

.

Null4.aac:

Equipment Damage Risk:

When installing seals, carefully align them so they are concen-

tric with the shaft hole. Apply insertion force across the entire 

face, or at least equally along the entire outside diameter (as 
close to the seal O.D. as possible). Seals are hollow metal 

structures and are somewhat fragile. The are not intended to 

be in contact with the bearings.

51. Carefully place drum/hub assembly

 on spindle.

52. Insert re-packed outer bearing

.

53. Add spindle washer

 and castle nut

.

54. Tighten nut until drum/hub does not turn freely. 

Loosen nut 

1

6

turn, and as much looser as needed 

to align hole in spindle (not shown) with notches in 

nut.

55. Secure nut with cotter pin

. Install dust cap

.

Null4:

Brake Failure Hazards:

Remove chips. Do not re-use heavily damaged or worn-out 

drums. Failure to remove chips can cause bearing failure, 

brake failure or wheel/spindle separation. Heavily scored, 
worn or oversized drums can reduce brake performance or 

cause loss of braking. This could result in death, serious per-

sonal injury, or property damage.

Figure 125

Brake Drum

29635

Non-Asbestos Fibers and Metal Dust Hazards:

Wear a respirator equipped with a HEPA filter approved by 

NIOSH or MSHA when grinding or machining brake drums. 
In addition, do such work in an area with a local exhaust ven-

tilation system equipped with a HEPA filter.

1

2

Null4:

Figure 126

Re-mount Hub and Drum

31378

1

2

3

4

5

6 7

8

3

4

5

6

7

8

Summary of Contents for NTA2007HD



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands