manualshive.com logo in svg

GRAPHTEC GL350, Service Manual, Page: 14 / 58

Share
Download
GRAPHTEC GL350 Service Manual Download Page 14

GL400-UM-251-9370 

3-1

3. DISASSEMBLY AND REASSEMBLY

3.  DISASSEMBLY AND REASSEMBLY

3.1  Notes on Disassembly and Reassembly

• During disassembly, disconnect the cables from the specified connectors as necessary.
• During reassembly, double-check to ensure that the proper cables have been correctly re-connected to 

the pertinent connectors.

• Some areas of the control panel unit possess a high electrical potential, so exercise caution to avoid an 

electrical shock.

• When handling the LCD shield and LCD protective plate, be careful not to leave fingerprints or other 

marks on them.

3.2  Mounting and Removing the Input Terminal Unit

This section describes how to mount and remove the input terminal unit.

CAUTION

• Make sure that the power supply has been turned off before mounting or removing the input terminal unit.

Removing the Input Terminal Unit

(1)  Remove the cover from the input terminal mounting area.

(2)  Press down on the lock button while pulling the input terminal unit towards you. At this time, grip the 

input terminal unit firmly while removing it.

Summary of Contents for GL350



























































Reviews:

No comments